SEM 내부에 설치된 트라이보 시험기를 통한 금속 코팅의 실시간 마찰/마모 특성 분석
Real Time Analysis of Friction/Wear Characteristics of Metal Coatings with a Tribo-tester Installed in an SEM
0
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
This study aims to visualize the friction and wear behaviors of metal coatings in real time. The main mechanism of wear is identified by observing all the processes in which wear occurs. The friction coefficients of the moments are monitored to confirm the relationship between the friction and wear characteristics of the coating. Thin Ag coatings, which are several hundred nanometers in thickness, are prepared by depositing Ag atoms on silicon substrates through a sputtering method. A pin-on-disk-type tribo-tester is installed inside a scanning electron microscope (SEM) to evaluate the friction and wear characteristics of the Ag coating. A fine diamond pin is brought into contact with the Ag coating surface, and a load of 20 mN is applied. The contact pressure is calculated to be approximately 15 GPa. The moments of wear caused by the sliding motion are visualized, and the changes in the friction characteristics according to each step of wear generation are monitored. The Ag coating can be confirmed to exhibit a wear phenomenon by gradually peeling off the surface of the coating on observing the friction and wear characteristics of the coating in real time inside the SEM. This can be explained by a typical plowing-type wear mechanism.
Abstract
This study aims to visualize the friction and wear behaviors of metal coatings in real time. The main mechanism of wear is identified by observing all the processes in which wear occurs. The friction coefficients of the moments are monitored to confirm the relationship between the friction and wear characteristics of the coating. Thin Ag coatings, which are several hundred nanometers in thickness, are prepared by depositing Ag atoms on silicon substrates through a sputtering method. A pin-on-disk-type tribo-tester is installed inside a scanning electron microscope (SEM) to evaluate the friction and wear characteristics of the Ag coating. A fine diamond pin is brought into contact with the Ag coating surface, and a load of 20 mN is applied. The contact pressure is calculated to be approximately 15 GPa. The moments of wear caused by the sliding motion are visualized, and the changes in the friction characteristics according to each step of wear generation are monitored. The Ag coating can be confirmed to exhibit a wear phenomenon by gradually peeling off the surface of the coating on observing the friction and wear characteristics of the coating in real time inside the SEM. This can be explained by a typical plowing-type wear mechanism.
참고문헌 (19)
- Zimmer, O., "Vacuum arc deposition by using a venetian blind particle filter", Surf. Coat. Technol, 200(1-4), pp.440~443 (2005)
- Montemor, M. F., "Functional and smart coatings for corrosion protection : A review of recent advances", Surf. Coat. Technol, 258, pp.17~37 (2014)
- Grouchko, M., "Formation of air-stable copper-silver core-shell nanoparticles for inkjet printing", J. Mater. Chem, 19(19), pp.3057~3062 (2009)
- Grouchko, M., "Silver(Ag)as anode and cathode current collectors in high temperature planar solid oxide fuel cells", Int. J. Hydrog. Energy, 36(1), pp.779~786 (2011)
- Sharma, M. K., "Creating conductive copper-silver bimetallic nanostructured coatings using a high temperature reducing jet aerosol reactor", Aerosol Sci. Technol, 47(8), pp.858866~ (2013)
- Song, J., "Correlation between friction and wear properties and electrical performance of silver coated electrical connectors", Wear, 330-331, pp.400~405 (2015)
- Holmberg, K., "Coatings tribology-contact mechanisms and surface design", Tribol. Int., 31(1-3), pp.107~120 (1998)
- Maillat, M., "Preparation of silver coatings to obtain low friction in alternating sliding at 570?", Surf. Coat. Technol, 61(1-3), pp.25~29 (1993)
- Penkov, O. V., "Design and construction of a micro-tribotester for precise in-situ wear measurements", Micromachines, 8(4), pp.103~ (2017)
- 김창래, "Investigation of Micro-Abrasion Characteristics of Thin Metallic Coatings by In-Situ SEM Scratch Test", International Journal of Precision Engineering and Manufacturing, 17(9), pp.1139~1147 (2016), 한국정밀공학회
- Murarash, B., "Tribometer for in situ scanning electron microscopy of microstructured contacts", Tribol. Lett, 41(2), pp.319~323 (2011)
- Kato, K., "Micro-mechanisms of wear-wear modes", Wear, 153(1), pp.277~295 (1992)
- Ghaednia, H., "A comprehensive study of the elasto-plastic contact of a sphere and a flat", Tribol. Int, 93, pp.78~90 (2016)
- Afferrante, L., "Interacting and coalescing Hertzian asperities : A new multiasperity contact model", Wear, 278-279, pp.28~33 (2012)
- Geng, X., "Mechanical stability under sliding contact of thin silver film embedded in brittle multilayer", Wear, 276-277, pp.111~120 (2012)
- Greaves, G. N., "Poisson’s ratio and modern materials", Nat. Mater, 10(11), pp.823~837 (2011)
- Bayram, B., "Plasma-activated direct bonding of diamond-on-insulator wafers to thermal oxide grown silicon wafers", Diam. Relat. Mat, 19(11), pp.1431~1435 (2010)
- Sakharova, N. A., "Influence of ductile interlayers on mechanical behaviour of hard coatings under depthsensing indentation : A numerical study on TiAlN", J. Mater. Sci, 45(14), pp.3812~3823 (2010)
- Kim, D. E., "A novel approach to wear reduction of micro-components by synthesis of carbon nanotube-silver composite coating", CIRP Ann-Manuf. Technol, 60(1), pp.599602~ (2011)