모래 3체 마모시험 장비(3-body abrasion tester)를 이용한 PLA프린팅 표면의 형상별 트라이볼로지 성능 분석
Tribology Performance Analysis by Surface Patterns of PLA Printing Samples Using 3-body Abrasion Tester
0
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
This study applies various surface patterns to minimize material loss in construction equipment that is subject to severe wear due to sand, such as the wear-resistant steel plates of dump trucks or the teeth of excavators. The relationship between surface morphology and wear behavior is investigated using PLA+ polymer to observe the effect of the surface pattern. Five types of samples - smooth, concave, convex, wavy concave, and wavy convex designs - are created using a 3D printer. A wear experiment is conducted for a duration of 3 h using 6.5 kg of abrasive particles. The mass loss of the samples after the experiment is measured to assess the extent of wear. Additionally, the surface morphology of the samples before and after the experiment is analyzed using SEM and confocal microscopy. The study results reveal that the smooth design exhibits the highest wear loss, whereas the concave and wavy concave designs show relatively lower wear loss. The convex and wavy convex designs exhibit varying contact areas with the abrasive particles depending on the surface pattern, resulting in different levels of wear. Furthermore, a comparison between the experimental results and DEM simulations confirms the observed wear trends. This study reveals the relationship between wear damage according to surface pattern shape and is expected to be of substantial help in the analysis of wear and tear on agricultural and heavy equipment.
Abstract
This study applies various surface patterns to minimize material loss in construction equipment that is subject to severe wear due to sand, such as the wear-resistant steel plates of dump trucks or the teeth of excavators. The relationship between surface morphology and wear behavior is investigated using PLA+ polymer to observe the effect of the surface pattern. Five types of samples - smooth, concave, convex, wavy concave, and wavy convex designs - are created using a 3D printer. A wear experiment is conducted for a duration of 3 h using 6.5 kg of abrasive particles. The mass loss of the samples after the experiment is measured to assess the extent of wear. Additionally, the surface morphology of the samples before and after the experiment is analyzed using SEM and confocal microscopy. The study results reveal that the smooth design exhibits the highest wear loss, whereas the concave and wavy concave designs show relatively lower wear loss. The convex and wavy convex designs exhibit varying contact areas with the abrasive particles depending on the surface pattern, resulting in different levels of wear. Furthermore, a comparison between the experimental results and DEM simulations confirms the observed wear trends. This study reveals the relationship between wear damage according to surface pattern shape and is expected to be of substantial help in the analysis of wear and tear on agricultural and heavy equipment.
참고문헌 (10)
- 공민선, "그리스 윤활하에서 레이저 표면 텍스쳐링된 그루브 빗살무늬 패턴의 사잇각에 따른 미끄럼 마찰특성 평가", 한국트라이볼로지학회지, 38(6), pp.261~266 (2022), 한국트라이볼로지학회
- 황성호, "표면 거칠기가 가스 포일 스러스트 베어링의 성능에 미치는 영향", 한국트라이볼로지학회지, 39(2), pp.81~85 (2023), 한국트라이볼로지학회
- Jian Song, "Correlation between Wear Resistance and Lifetime of Electrical Contacts", Advances in Tribology (2012)[DOI]
- Jia Chen, "Determining Tribocorrosion Rate and Wear-Corrosion Synergy of Bulk and Thin Film Aluminum Alloys", Journal of Visualized Experiments (2018)[DOI]
- A. Maurel-Pantel, "A thermo-mechanical large deformation constitutive model for polymers based on material network description : Application to a semi-crystalline polyamide 66", International Journal of Plasticity, 67, pp.102~126 (2015)
- Qing Ji, "Mechanical Properties and a Constitutive Model of 3D-Printed Copper Powder-Filled PLA Material", Surface & Coatings Technology, 409, pp.126843~ (2021)
- D. Forsström, "Calibration and validation of a large scale abrasive wear model by coupling DEM-FEM Local failure prediction from abrasive wear of tipper bodies during unloading of granular material", Engineering Failure Analysis, 66, pp.274~283 (2016)
- L. Godino, "Modelling the wear evolution of a single alumina abrasive grain : Analyzing the influence of crystalline structure", Journal of Materials Processing Tech, 277, pp.116464~ (2020)
- Yunpeng Yan, "Modelling of material removal due to sliding wear caused by bulk material", Powder Technology, 415, pp.118109~ (2023)
- Yunpeng Yan, "The Influence of Particle Size on Sliding Wear of a convex Pattern Surface", Minerals, 12(139) (2022)