Silicone Index Tooth Tray를 이용한 인상체의 체적안정성에 대한 연구
DIMENSIONAL STABILITY OF IMPRESSION BODY USING SILICONE INDEX TOOTH TRAY IMPRESSION SYSTEM
1
조회
0
다운로드
0
인용
0
참고문헌
초록
Abstract
Statement of problem: Silicone Index Tooth Tray impression system which does not use gingicord has a shortcoming. It takes time to remove internal wall of Silicone Index Tooth Tray for space of wash impression material. Purpose: This study was to evaluate whether providing certain space to impression body can prevent from doing complicated laboratory work. Material and methods: After mounting metal dies with shoulder and chamfer margins arbiturarily, SITT was produced using Blu-mousse. In one experimental group, wash impression was taken using Fit-tester without removing interior surface of SITT and in the other group, wash impression was taken using Fit-tester providing 0.5mm space in the SITT and then compared the differences in two groups. Results: 1. There was no significant difference between a group which did not allow space and a group which granted equal 0.5mm space. 2. There was no significant difference between gingival diameter, occlusal diameter of metal die that has shoulder margin and gingival diameter, occlusal diameter of metal die that has chamfer margin. 3. There was no significant difference between a group which did not take pick-up impression and a group which took pick-up impression through relining method using SITT. 4. There was no significant difference between a group that poured immediately after taking primary impression and a group that poured after removing poured stone die. Conclusions: When taking an impression of an abutment using SITT impression system, it is considered to obtain clinically identical results between a group that did not grant a 0.5mm space within SITT for wash impression and a group which invest a space. Furthermore, it is considered possible to produce an individual die through secondary pouring.
참고문헌 (18)
- "Currentmethods of finish-line exposure by practicingprosthodontists", 8, pp.163~170 (1999)
- "Copper-bandgingival retraction to produce void-freecrown and bridge impressions", pp.513~516 (1973)
- "A study onAccaracy and Dimensional Stability ofImpression gody according to Techniquesand Directions of Impression taking", 37, pp.567~80 (1999)
- "The matrix impression sys-tem for fixed prosthodontics", 79, pp.208~15 (1998)
- "Secondary soften-ing of modeling compound for copper bandimpressions", 49(ldi g), pp.361~362 (1983)
- "an alternative techniquefor taking difficult crown and bridge im-pressions with minimal gingival trauma", pp.555~560 (1989), Tube impressions
- "Cordless tissue re-traction for impressions for fixed pros-thesis", pp.379~86 (1967)
- "Effect of relief space and escapeholes on pressure characteristics of maxil-lary edentulous impressions", 91, pp.570~576 (2004)
- "A methodologyfor quantitative evaluation of root canal in-strumentation using microcomputed to-mography", 34, pp.309~318 (2001)
- "The ef-fect of tray selection viscosity of impres-sion material and sequence of pour on theaccuracy of dies made from dual-archimpressions", 90, pp.143~149 (2003)
- "Anevaluation of the time-dependent dimen-sional stability of eleven elastomeric im-pression materials", 52, pp.120~125 (1984)
- "Accuracy and bondstrength of reversible with irreversiblehydrocolloid impression systems", 68, pp.578~584 (1992)
- "Bondstrength and accuracy of combined re-versible-irreversible hydrocolloid impres-sion systems", 67, pp.621~627 (1992)
- "Gingival mar-gins for crowns", 64, pp.636~642 (1990)
- "An analysis of mar-gin configurations for metal-ceramiccrowns", 53, pp.153~157 (1985), Prince J
- "Dimensional accuracy of dental casts in-fluence of tray material", 11, pp.98~108 (2002), impression material
- "Accuracy of fourtypes of rubber impression materials com-parred with time of pour and a repeat pourof models", 53, pp.484~490 (1985)
- "Accuracy of fourtypes of rubber impression materials com-parred with time of pour and a repeat pourof models", pp.484~490 (1985)