부식된 철근의 부착강도 및 정착길이 산정모델
Bond Strength and Development Length Model for Corroded Reinforcing Bars
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
This study aims to propose a simplified equation for estimating the bond strength of corroded reinforcing bars. To this end, extensive parametric analyses were performed using the detailed analysis method presented in the authors’ previous study, where a wide range of critical variables were considered, such as compressive strength of concrete, net cover thickness, and reinforcing bar diameter. The sensitivity in bond strength of the corroded reinforcing bar according to each variable was evaluated. On this basis, a simplified formula for the bond strength of the corroded reinforcing bar was derived through regression analysis. The proposed equation was rigorously tested and verified using the bond test results of corroded reinforcing bars collected from the literature. The results confirmed that the proposed equation could estimate the bond strengths of specimens with better accuracy than the existing models, providing a reliable tool for engineers and researchers. In addition, the proposed equation was used to analyze the development length required for corroded tensile reinforcement to exert its yield strength, and it showed that the cover thickness of concrete must be at least four times the diameter of the reinforcing bar to achieve the yielding strength of reinforcing bar even at a corrosion degree of more than 5.0%.
Abstract
This study aims to propose a simplified equation for estimating the bond strength of corroded reinforcing bars. To this end, extensive parametric analyses were performed using the detailed analysis method presented in the authors’ previous study, where a wide range of critical variables were considered, such as compressive strength of concrete, net cover thickness, and reinforcing bar diameter. The sensitivity in bond strength of the corroded reinforcing bar according to each variable was evaluated. On this basis, a simplified formula for the bond strength of the corroded reinforcing bar was derived through regression analysis. The proposed equation was rigorously tested and verified using the bond test results of corroded reinforcing bars collected from the literature. The results confirmed that the proposed equation could estimate the bond strengths of specimens with better accuracy than the existing models, providing a reliable tool for engineers and researchers. In addition, the proposed equation was used to analyze the development length required for corroded tensile reinforcement to exert its yield strength, and it showed that the cover thickness of concrete must be at least four times the diameter of the reinforcing bar to achieve the yielding strength of reinforcing bar even at a corrosion degree of more than 5.0%.
참고문헌 (23)
- Han SJ, "Degradation of flexural strength in reinforced concrete members caused by steel corrosion", Constr Build Mater, 54(1), pp.572~583 (2014)
- Tran DVP, "Prediction equations for corrosion rate of reinforcing steel in cement-fly ash concrete", J Struct Integr Maint, 8(2), pp.1~11 (2023)
- Lakshmi A, "Influence of corrosion-based section loss on morphology and tensile capacity of pre-stressing strands", J Struct Integr Maint, 9(1), pp.91~99 (2024)
- Oh BH, "Critical corrosion amount to cause cracking of reinforced concrete structures", ACI Mater J, 106(4), pp.333~339 (2009)
- Al-Sulaimani GJ, "Influence of corrosion and cracking on bond behavior and strength of reinforced concrete members", ACI Struct J, 87(23), pp.220~231 (1990)
- Almusallam AA, "Effect of reinforcement corrosion on bond strength. construction and building materials", Constr Build Mater, 10(2), pp.123~129 (1996)
- Cabrera JG, "Deterioration of concrete due to reinforcement steel corrosion", Cem Concr Compos, 18(1), pp.47~59 (1996)
- Lee HS, "Evaluation of the bond properties between concrete and reinforcement as a function of the degree of reinforcement corrosion", Cem Concr Res, 32(1), pp.1313~1318 (2002)
- Fang C, "Corrosion influence on bond in reinforced concrete", Cem Concr Res, 34(11), pp.2159~2167 (2004)
- Chung L, "Bond strength prediction for reinforced concrete members with highly corroded reinforcing bars", Cem Concr Compos, 30(7), pp.603~611 (2008)
- Maaddawy TE, "Analytical model to predict nonlinear flexural behavior of corroded reinforced concrete beams", ACI Struct J, 102(4), pp.550~559 (2005)
- Bhargava K, "Models for corrosion-induced bond strength degradation in reinforced concrete", ACI Mater J, 104(6), pp.594~603 (2007)
- Stanish K, "Corrosion Effects on Bond Strength in Reinforced Concrete", ACI Struct J, 96(6), pp.915~921 (1999)
- Auyeung Y, "Bond behavior of corroded reinforcement bars", ACI Mater J, 97(2), pp.214~220 (2000)
- Xu YL, "Experimental study of anchorage properties for deformed bars in concrete", PhD, pp.1990
- Chen WF, "Plasticity in reinforced concrete", pp.363~ (1982), McGraw-Hill
- Wang XH, "Modeling bond strength of corroded reinforcement without stirrups", Cem Concr Res, 34(8), pp.1331~1339 (2004)
- Pantazopoulou SJ, "Modeling cover-cracking due to reinforcement corrosion in RC structures", Journal of Engineering Mechanics Division, 127(4), pp.342~351 (2001)
- Coronelli D, "Corrosion cracking and bond strength modeling for corroded bars in reinforced concrete", ACI Struct J, 99(3), pp.267~276 (2002)
- Ka SB, "Bond strength of reinforcing bars considering failure mechanism", Eng Fail Anal, 94, pp.327~338 (2018)
- A Theory of bond applied to overlapping tensile reinforcement splices for deformed bars, "Tefers R", Division of concrete Structures, Chalmers University of Technology, 2~, pp.Publication 73 (1973)
- "Korean Design Standard, KDS 14 20 52 - Design Standard for Development and Splices in Concrete Structures", ~ (2022)
- European Committee for Standardization, "Eurocode 2: Design of Concrete Structures Part 1-1: General Rules and Rules for Building (EM 1994-1-1: 2004)", ~ (2004)