Experimental investigation and design method of the general anchorage zone in the ring beam of prestressed concrete containment vessels
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Ring beam is the main anchorage zone of the tendons in the nuclear power prestressed concrete containment vessel (PCCV). Its safety is crucial and has a great influence on the overall performance of PCCV. In this paper, two half-scale ring beams were tested to investigate the mechanical performance of the anchorage zone in the PCCV under multidirectional pressure. The effect of working condition with different tension sequences was investigated. Additionally, a half axisymmetric plane model of the containment was established by the finite element simulation to further predict the experimental responses and propose the local reinforcement design in the anchorage zone of the ring beam. The results showed that the ultimate load of the specimens under both working conditions was greater than the nominal ultimate tensile force. The original reinforcement design could meet the bearing capacity requirements, but there was still room for optimization. The ring beam was generally under pressure in the anchorage area, while the splitting force appeared in the under-anchor area, and the spalling force appeared in the corner area of the tooth block, which could be targeted for local strengthening design.
Abstract
Ring beam is the main anchorage zone of the tendons in the nuclear power prestressed concrete containment vessel (PCCV). Its safety is crucial and has a great influence on the overall performance of PCCV. In this paper, two half-scale ring beams were tested to investigate the mechanical performance of the anchorage zone in the PCCV under multidirectional pressure. The effect of working condition with different tension sequences was investigated. Additionally, a half axisymmetric plane model of the containment was established by the finite element simulation to further predict the experimental responses and propose the local reinforcement design in the anchorage zone of the ring beam. The results showed that the ultimate load of the specimens under both working conditions was greater than the nominal ultimate tensile force. The original reinforcement design could meet the bearing capacity requirements, but there was still room for optimization. The ring beam was generally under pressure in the anchorage area, while the splitting force appeared in the under-anchor area, and the spalling force appeared in the corner area of the tooth block, which could be targeted for local strengthening design.
참고문헌 (27)
- S. Wang, "Design of radial reinforcement for prestressed concrete containments", Nucl. Eng. Des, pp.255~ (2013)
- J. Qian, "Pseudo-dynamic tests of a 1:10 model of pre-stressed concrete containment vessel for CNP1000 nuclear power plant", China Civ. Eng. J, 06, pp.7~13 (2007)
- J. Liu, "Experimental study on a large aircraft impacting reinforced concrete nuclear containment structure model", J. Build. Struct, 08(43), pp.185~195 (2022)
- F. Wang, "A scaled test on the damage and vibration behavior of reinforced concrete nuclear containment subjected to a large aircraft impact", Eng. Struct, (268), pp.114755~ (2022)
- Z. Xia, "Design research & model experiment of containment in 1000MW NPP", Nucl. Power Eng. S, (S1), pp.123~129 (2002)
- R. M. Parmar, "Over-pressure test on BARCOM pre-stressed concrete containment", Nucl. Eng. Des, (269), pp.177~183 (2014)
- Overpressurization Test of a 1:4-scale Prestressed Concrete Containment Vessel Model, "M.F. Hessheimer", Sandia National Laboratories, ~, pp.NUREG (2003), CR-6810
- T. Sugano, "Full-scale aircraft impact test for evaluation of impact force", Nucl. Eng. Des, 03(140), pp.373~385 (1993)
- S. Jin, "Fragility analysis and probabilistic performance evaluation of nuclear containment structure subjected to internal pressure", Reliab. Eng. Syst. Saf, 208, pp.107400~ (2021)
- S. Jin, "Nonlinear finite element analysis of prestressed concrete containment vessel under severe accident loads", KSCE J. Civ. Eng, 24(3), pp.816~825 (2020)
- Q. Peng, "Response analysis of nuclear power plant containment under earthquake and internal pressure", Acta Sci. Nat. Univ. Sunyatseni, 06(58), pp.73~80 (2019)
- A. Shokoohfar, "Nonlinear analysis of pre-stressed concrete containment vessel(PCCV)using the damage plasticity model", Nucl. Eng. Des, (298), pp.41~50 (2016)
- K. Lee, "Analysis of impact of large commercial aircraft on a prestressed containment building", Nucl. Eng. Des, (265), pp.431~449 (2013)
- D. A. Makhloof, "Identification and assessment of seismic damage for RC containment structures considering prestressing effect", Eng. Fail. Anal, (141), pp.106645~ (2022)
- S. Jin, "A simplified fragility analysis methodology for containment structure subjected to overpressure condition", Int. J. Pres. Ves. Pip, (184), pp.104104~ (2020)
- S. Wang, "Analytical evaluation of the dome-cylinder interface of nuclear concrete containment subjected to internal pressure and thermal load", Eng. Struct, (161), pp.1~7 (2018)
- Z. Zhou, "Mechanical analysis for prestressed concrete containment vessels under loss of coolant accident", Comput. Concr, 14(2), pp.127~143 (2014)
- Y. Yang, "Numerical simulation analyses of damage and vibration response of a nuclear power plant under aircraft impact", J. Vib. Shock, 04(42), pp.312~324 (2023)
- H. Jiang, "Aircraft impact analysis of nuclear safety-related concrete structures : a review", Eng. Fail. Anal, (46), pp.118~133 (2014)
- M. R. Sadique, "Nuclear containment structure subjected to commercial and fighter aircraft crash", Nucl. Eng. Des, (260), pp.30~46 (2013)
- J. Schlaich, "Toward a consistent design of structural concrete", PCI J, 32(3), pp.74~150 (1987)
- Z. -Q. He, "Three-dimensional spreading of prestressing forces in box girders", Structures, 33, pp.4803~4816 (2021)
- L. Zhou, "Elastic-to-plastic strut-and-tie model for multianchorage zones", Struct. Concr, 19(4), pp.1049~1062 (2018)
- C. Marchao, "Optimization of anchorage corner blisters for post-tensioning tendons", Struct. Concr, 18(2), pp.334~348 (2017)
- D. -W. Hou, "Investigation and improvement of strutand-tie model for design of end anchorage zone in post-tensioned concrete structure", Construct. Build. Mater, 136, pp.482~494 (2017)
- Building Code Requirements for Structural Concrete:ACI 318M-14, "American Concrete Institute", American Concrete Institute, ~ (2014)
- AASHTO, "AASHTO LRFD Bridge Design Specifications" (2014), American Association of State Highway and Transportation Officials