온도변화에 따른 나노 복합재료의 충격거동
Impact behavior on temperature effect of nano composite materials
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
In this study, the effect of temperature effect of the rubber matrix filled with nano sized silica particles composites with silica volume fraction of 19–25% was investigated by the Charpy impact test. The Charpy impact test was conducted in the temperature range from –40℃ to 0℃. The critical energy release rate GIC of the rubber matrix composites filled with nano sized silica particles was considerably affected by temperature and it was shown that the maximum value was appeared at higher temperature between temperature tested and it was shown that the value of GIC increases as temperature tested increases. The major fracture mechanisms were matrix deformation, silica particle debonding and delamination, microcrack between particles and matrix, and/or pull out between particles and matrix which is ascertained by SEM photographs of Charpy impact surfaces fracture.
Abstract
In this study, the effect of temperature effect of the rubber matrix filled with nano sized silica particles composites with silica volume fraction of 19–25% was investigated by the Charpy impact test. The Charpy impact test was conducted in the temperature range from –40℃ to 0℃. The critical energy release rate GIC of the rubber matrix composites filled with nano sized silica particles was considerably affected by temperature and it was shown that the maximum value was appeared at higher temperature between temperature tested and it was shown that the value of GIC increases as temperature tested increases. The major fracture mechanisms were matrix deformation, silica particle debonding and delamination, microcrack between particles and matrix, and/or pull out between particles and matrix which is ascertained by SEM photographs of Charpy impact surfaces fracture.
참고문헌 (11)
- Bonner M, "The mechanical properties of high stiffness hot–compacted polypropylene: a new development", J Mater Sci, 49, pp.1606~1611 (2014)[DOI]
- Chen LS, "Impact fracture energy of mineral–filled polypropylene", Polymer Eng Sci, 29(8), pp.505~512 (1989)
- 김병탁, "온도변화에 따른 유리섬유", 폴리우레탄 복합재료의 충격파괴거동, 2009, pp.45(3), 188~193[DOI]
- Kwon DJ, "Improvement of mechanical and interfacial properties of carbon fiber", epoxy composites by adding nano SiC fillers, 2013, pp.14(2), 75~81
- 장상희, "생분해성 고분자 나노복합체의 형태학 및 기계적 특성 연구", 청정기술, 19(4), pp.401~409 (2013), 한국청정기술학회[DOI]
- Jung WY, "Impact performance and toughening mechanisms of toughness–tailored polypropylene impact copolymer", J Mater Sci, 48, pp.1275~1282 (2013)[DOI]
- 이정규, "입자 함유율의 변화에 따른 나노 실리카 복합재료의 충격파괴거동", 한국어업기술학회지, 51(3), pp.454~460 (2015), 한국어업기술학회
- Munro M, "The elevated temperature dependence of fracture energy mechanisms of hybrid carbon–glass fiber reinforced composites", J Mater Sci, 23, pp.3129~3138 (1988)
- Plati E, "The determination of the fracture parameters of polymers in impact", Polymers Eng Sci, 15, pp.470~477 (1975)
- Salehi Vaziri H, "Investigation of the fracture mechanism and mechanical properties of polystyrene", silica nanocomposite in various silica contents, 2011, pp.46, 5628~5638
- Tam WY, "Impact properties of glass fibre", impact modifier, J Mater Sci, pp.2000, 35[DOI]