실리콘 인상재의 보관온도에 따른 특성변화
The Property Change of Silicone Impression Materials with Change of Storage Temperature
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
The purpose of this study was to evaluate the physical properties of hydrophilic polyvinyl siloxane impression materials as change of material's storage temperatures. Working time, strain-in-compression, elastic recovery and consistency were tested according to ISO Standard NO. 1563. The results are as followed. 1. Working time decreased in cold storage. 2. Strain-in-compression was different in storage temperatures. Material's strain-in compression in cold temperatures were higher than in room temperature and in incubator. 3. A coefficient of elastic recovery varied by storage temperatures. The rate in cold temperature was the lowest and in incubator was the highest. 4. Consistency of impression substance different in storage temperatures. The extent in cold temperature is the highest and in incubator was the lowest. Statistical analysis(SPSS 14.0k, p>0.05) showed that storage temperature affect to material's physical properties. We recognized that the physical properties of polyvinyl siloxane impression materials were changed according to storage temperature.
Abstract
The purpose of this study was to evaluate the physical properties of hydrophilic polyvinyl siloxane impression materials as change of material's storage temperatures. Working time, strain-in-compression, elastic recovery and consistency were tested according to ISO Standard NO. 1563. The results are as followed. 1. Working time decreased in cold storage. 2. Strain-in-compression was different in storage temperatures. Material's strain-in compression in cold temperatures were higher than in room temperature and in incubator. 3. A coefficient of elastic recovery varied by storage temperatures. The rate in cold temperature was the lowest and in incubator was the highest. 4. Consistency of impression substance different in storage temperatures. The extent in cold temperature is the highest and in incubator was the lowest. Statistical analysis(SPSS 14.0k, p>0.05) showed that storage temperature affect to material's physical properties. We recognized that the physical properties of polyvinyl siloxane impression materials were changed according to storage temperature.
참고문헌 (28)
- Korean Dental Materials Professor Association, "Dental Materials. 5th ed", Koonja, 125~159 (2006)
- Klooster J, "Effect of strain rate on the behavior of elastomeric impression", J Prosthet Dent, 66(3), pp.292~298 (1991)
- Goldberg AJ, "Viscoelastic properties of silicone, polysulfide, and polyether impression materials", J Dent Res, 5(53), pp.1033~1039 (1974)
- Tjan AH, "Clinically oriented evaluation of the accuracy of commonly used impression materials", J Prosthet Dent, 56(1), pp.4~8 (1986)
- Dounis GS, "A comparison of impression materials for complete-arch fiexd partial dentures", J Prosthet Dent, 65(2), pp.165~169 (1991)
- Yeh CL, "Properties of addition-type silicone impression materials", J Am Dent Assoc, 101(3), pp.482~484 (1980)
- Lacy AM, "Time-dependent accuracy of elastomer impression materials. Part II: Polyether, polysulfides, and polyvinylsiloxane", 45(3), pp.329~333 (1981)
- 김광만, "부가중합형 실리콘 인상재의 표면 친수성이 미세부 재현성에 미치는 영향", 대한치과기재학회지, 30(3), pp.299~306 (2003), 대한치과기재학회
- Robert S, "Effect of surface treatments on the wettability of vinyl polysiloxane impression materials", J Prosthet Dent, 84(1), pp.98~102 (2000)
- Michael NM, "Polyvinyl siloxane impression materials: an update on clinical use", Aust Dent J, 43(6), pp.428~434 (1998)
- Millar BJ, "A comarison of three wetting agents used to facilitate the pouring of dies", J Prosthet Dent, 74(4), pp.341~344 (1995)
- Erkut S, "Effects of glow-discharge and surfactant treatments on the wettability of vinyl polysiloxane impression materials", J Prosthet Dent, 93(4), pp.356~363 (2005)
- Marcinak CF, "Linear dimensional changes in addition curing silicone impression materials", J Prosthet Dent, 47(4), pp.411~413 (1982)
- Fano V, "Dimensional stability of silicone-based impression materials", Dental Materials, 8(2), pp.105~109 (1992)
- Chew CL, "The influence of temperature on the dimensional stability of poly (vinyl siloxane) impression materials", Int J Prosthodont, 6(6), pp.528~532 (1993)
- John CB, "Temperature effects on the rheological properties of current polyether and polysiloxane impression materials during setting", J Prosthet Dent, 90(2), pp.150~161 (2003)
- Ravi P, "Long-term dimensional stability and reproduction of surface detail of four polyvinyl siloxane duplication materials", J Dent, 36(6), pp.456~461 (2008)
- McCabe JF, "Rheological properties of elastomeric impression materials before and during setting", J Dent Res, 77(11), pp.1874~1480 (1998)
- McConnell RJ, "Working time of synthetic elastomeric impression materials", J Can Dent Assoc, 60(1), pp.49~54 (1994)
- John HP, "The effects of different storage conditions on polyether and polyvinylsiloxane impressions", J Am Dent Assoc, 129(7), pp.1014~1021 (1998)
- 황수영, "항균필러가 첨가된 치과용 실리콘 고무인상재", 박사, pp.2008
- Finger WJ, "Significance of filler content to properties of silicone impression materials", Dent Mater, 4(1), pp.33~37 (1988)
- Chen SY, "Factors affecting the accuracy of elastometric impression materials", J Dent, 32(8), pp.603~609 (2004)
- John C, "Clinically relevant mechanical properties of elastomeric impression materials", Int J Prosthodont, 11(3), pp.219~223 (1998)
- Lorren RA, "The contact angle of die stone on impression materials", J Prosthet Dent, 36(2), pp.176~180 (1976)
- Pratten DH, "Wettability of a hydrophilic addition silicone impression material", J Prosthet Dent, 61(2), pp.197~202 (1989)
- Panichuttra R, "Hydrophilic poly(vinylsiloxane) impression materials: dimensional accuracy, wettability, and effect on gypsum hardness", Int J Prosthodont, 4(3), pp.240~248 (1991)
- Kim SH, "Change of surface property of dental impression materials according to time and disinfection", Surf Interface Anal, 40(3), pp.188~191 (2008)