Effect of moisture and drying time on the bond strength of the one-step self-etching adhesive system
1
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
Objectives: To investigate the effect of dentin moisture degree and air-drying time on dentin-bond strength of two different one-step self-etching adhesive systems. Materials and Methods: Twenty-four human third molars were used for microtensile bond strength testing of G-Bond and Clearfil S3 Bond. The dentin surface was either blot-dried or air-dried before applying these adhesive agents. After application of the adhesive agent, three different air drying times were evaluated: 1, 5, and 10 sec. Composite resin was build up to 4 mm thickness and light cured for 40 sec with 2separate layers. Then the tooth was sectioned and trimmed to measure the microtensile bond strength using a universal testing machine. The measured bond strengths were analyzed with three-way ANOVA and regression analysis was done (p = 0.05). Results:All three factors, materials, dentin wetness and air drying time, showed significant effect on the microtensile bond strength. Clearfil S3 Bond, dry dentin surface and 10sec air drying time showed higher bond strength. Conclusions: Within the limitation of this experiment, air drying time after the application of the one-step self-etching adhesive agent was the most significant factor affecting the bond strength, followed by the material difference and dentin moisture before applying the adhesive agent.
Abstract
Objectives: To investigate the effect of dentin moisture degree and air-drying time on dentin-bond strength of two different one-step self-etching adhesive systems. Materials and Methods: Twenty-four human third molars were used for microtensile bond strength testing of G-Bond and Clearfil S3 Bond. The dentin surface was either blot-dried or air-dried before applying these adhesive agents. After application of the adhesive agent, three different air drying times were evaluated: 1, 5, and 10 sec. Composite resin was build up to 4 mm thickness and light cured for 40 sec with 2separate layers. Then the tooth was sectioned and trimmed to measure the microtensile bond strength using a universal testing machine. The measured bond strengths were analyzed with three-way ANOVA and regression analysis was done (p = 0.05). Results:All three factors, materials, dentin wetness and air drying time, showed significant effect on the microtensile bond strength. Clearfil S3 Bond, dry dentin surface and 10sec air drying time showed higher bond strength. Conclusions: Within the limitation of this experiment, air drying time after the application of the one-step self-etching adhesive agent was the most significant factor affecting the bond strength, followed by the material difference and dentin moisture before applying the adhesive agent.
참고문헌 (19)
- Frankenberger R, "Technique sensitivity of dentin bonding: effect of application mistakes on bond strength and marginal adaptation", Oper Dent, 25, pp.324~330 (2000)
- Soderholm KJ, "Shear bond strength of one etchand- rinse and five self-etching dental adhesives when used by six operators", Acta Odontol Scand, 66, pp.243~249 (2008)
- Perdigão J, "New developments in dental adhesion", Dent Clin North Am, 51, pp.333~357 (2007)
- Van Landuyt KL, "Are onestep adhesives easier to use and better performing? Multifactorial assessment of contemporary one-step self-etching adhesives", J Adhes Dent, 11, pp.175~190 (2009)
- Van Meerbeek B, "Buonocore memorial lecture. Adhesion to enamel and dentin: current status and future challenges", Oper Dent, 28, pp.215~235 (2003)
- Yiu CK, "Effect of dentinal surface preparation on bond strength of self-etching adhesives", J Adhes Dent, 10, pp.173~182 (2008)
- Kitayama S, "Enamel bonding of self-etch and phosphoric acidetch orthodontic adhesive systems", Dent Mater J, 26, pp.135~143 (2007)
- Chiba Y, "Influence of moisture conditions on dentin bond strength of single-step selfetch adhesive systems", J Oral Sci, 48, pp.131~137 (2006)
- Di Hipólito V, "SEM evaluation of contemporary self-etching primers applied to ground and unground enamel", J Adhes Dent, 7, pp.203~211 (2005)
- 진명욱, "Self-etching adhesive system에서 수분 조절이 레진의 치질접착강도에 미치는 영향", Restorative Dentistry and Endodontics, 27(4), pp.363~369 (2002), 대한치과보존학회
- Werner JF, "Effect of relative humidity on bond strength of self-etching adhesives to dentin", J Adhes Dent, 4, pp.277~282 (2002)
- Nakaoki Y, "Effect of double-application of all-in-one adhesives on dentin bonding", J Dent, 33, pp.765~772 (2005)
- Jacobsen T, "Air-drying time of self-etching adhesives vs adhesive efficacy", J Adhes Dent, 8, pp.387~392 (2006)
- Chiba Y, "Effect of air-drying time of single-application self-etch adhesives on dentin bond strength", Oper Dent, 31, pp.233~239 (2006)
- Van Landuyt KL, "Origin of interfacial droplets with one-step adhesives", J Dent Res, 8, pp.739~744 (2007)
- Hiraishi N, "Technique sensitivity associated with air-drying of HEMA-free, single-bottle, one-step self-etch adhesives", Dent Mater, 23, pp.498~505 (2007)
- Van Landuyt KL, "The role of HEMA in one-step self-etch adhesives", Dent Mater, 24, pp.1412~1419 (2008)
- Tay FR, "Micromorphological spectrum from overdrying to overwetting acidconditioned dentin in water-free acetone-based, singlebottle primer", adhesives, 1996, pp.12, 236~244
- Tsuchimoto Y, "Effect of 4-MET- and 10-MDP-based primers on resin adhesive to titanium", Dent Mater J, 25, pp.120~124 (2006)