수종의 단일병 접착제의 적용 시간 연장이 건조 상아질의 미세인장 결합강도에 미치는 영향
Effect of increasing application time of single bottle adhesives to microtensile bond strength of dried dentin
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
본 연구는 친수성 용매가 함유되어 있는 3종의 단일병 접착제의 적용 시간을 증가시켰을 때, 건조 상아질에 대한 재 습윤의 효과가 있는지를 미세인장 결합강도의 측정을 통해 알아보고자 시행하였다. 실험대상은 최근에 발거한 상하악의 대구치로, 교합면 1/3 부위의 치질을 치아 장축에 수직으로 절단하여 상아질을 노출 시킨 후, 32%인산 (Unietch, Bisco Inc., Schaumburg, IL, USA) 으로 15초간 산부식 하고 수세하였다. 치아는 무작위로 S군 (Single Bond), O군 (One-Step), P군 (Prime & Bond NT)으로 분류하였고, 각 군은 다시 3군 (W: 상아질 표면의 남아있는 과잉의 물을 수분에 적신 거즈를 이용하여 제거한 후, 즉시 단일병 접착제를 적용하고 광중합, D: 30초간 건조 한 후 즉시 단일병 접착제를 적용하고 광중합, 30: 30초간 건조 한 후 단일병 접착제를 30초간 적용하고 광중합)으로 소 분류 하였다. 접착제 도포 후, 복합레진을 축조하고 접착계면이 1mm2가 되도록 절단 하여 각 군당 20개의 표본을 사용하여 미세인장 결합강도를 측정하였다. S군, O군의 30초 적용군 (S-30, O-30)은 건조군 (S-D, O-D)보다 높은 미세인장 결합강도를 보였으며, S-30군의 경우 S-D군보다 통계학적으로 유의성 있게 높았다 (P<0.05). 하지만, P군의 30초 적용군 (P-30)은 건조군 (P-D)에 비해 미세인장 결합강도가 통계학적으로 유의성 있게 감소하였다 (P<0.05).
Abstract
The purpose of this study was to evaluate the effect of increasing application time of single bottle adhesives (SBA) to microtensile bond strength (MTBS) of dried dentin. To expose the superficial dentin surfaces, human molars were sectioned perpendicular to the long axis of tooth. 32% phosphoric acid gels were applied for 15s and rinsed. The teeth were randomly assigned to 3 groups ; S group (Single Bond), O group (One-Step), P group (Prime & Bond NT). Each group was divided to 3 subgroups (W: dentin wipe with wet gauge and light cured immediately, D: dentin dried for 30s and light cured immediately, 30: dentin dried for 30s and light cured after applying SBA for 30s). Composite resin was built up on the dentin surface and sectioned to obtain 20 specimens with 1mm2 cross sectional area and the MTBS was measured. For Single Bond, the mean MTBS of S-W and S-30 group were higher than that of S-D group statistically (P<0.05). For One-Step, the mean MTBS of O-D group was statistically lower than that of O-W group (P<0.05). For Prime & Bond NT, the mean MTBS of P-30 group was statistically lower than that of P-D group (P<0.05).
참고문헌 (21)
- "Moist versus dry dentin:its effect on shear bond strength", pp.127~129 (1992)
- "Resin bonding to wet substrate Bonding to dentin", pp.39~41 (1992)
- "Permeability of dentin to adhesive agents", pp.618~631
- "Effect of drying on bonding strength", pp.~1029 (1991)
- "Micromorphological spectrum from overdrying to overwetting acid-conditioned dentin in water-free acetone-based", 12, pp.236~244 (1996)
- "A TEM study of two water-based adhesive systems bonded to dry and wet dentin", 77(1), pp.50~59 (1998)
- "Effect of solvent and re-wetting time on dentin adhesion", 32(5), pp.385~390 (2001)
- "Effect of a re-wetting agent on performance of acetone based dentin adhesives", 11, pp.207~213 (1999)
- "Dentin Bond strength after air drying and rewetting", 7(3), pp.144~148 (1994)
- "Ultrastructure of the resin-dentin interface following reversible and irreversible re-wetting", 10, pp.77~82 (1997)
- "Effects of different re-wetting techniques on dentin sheer bond strengths", 12(2), pp.85~96 (2000)
- "AFM study of drying and rehydration of etched dentin", 75, pp.390~ (1996)
- "The effect of a re-wetting agent on dentin bonding", 15, pp.282~295 (1999)
- "The promotion of adhesion by infiltration of monomers into tooth substrates", 6, pp.265~273 (1982)
- "Shear bond strength to moist and dry dentin of four dentin bonding systems", 13(4), pp.267~270
- "Dentin bond strength after air drying and rewetting", 7(3), pp.144~148 (1994)
- "Comparative microtensile bond strength and SEM analysys of bonding to wet and dry dentin", 13, pp.324~328 (2000)
- "Moisture spectrum of demineralized dentin for different solvent-based adhesive system", 5, pp.183~192 (2003)
- "Effect of resin primer solvents and surface wetness on resin composite bond strength to dentin", 5, pp.213~215 (1992)
- "Some effects of water on dentin bonding", 11, pp.132~136 (1995)
- "Some effects of water on dentin bonding", 11, pp.132~136 (1995)