Ultimate strength of simply supported plate with opening under uniaxial compression
2
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
Unstiffened plates are integral part of all kinds of structures such as ship and offshore oil platforms. Openings are unavoidable and absolutely reduce the ultimate strength of structures. In this study, the finite element analysis package, ABAQUS, is used to analyze the behavior of unstiffened plate with rectangular opening. The rectan¬gular opening form is divided into two cases. In case1, opening depth is constant, but opening width is varied. Mean¬while, in case2 opening width is fixed and opening depth is varied. Besides, for the two different form opening, the effect of plate slenderness parameter (β), opening area ratio (AR) and opening position ratio (PR) on the ultimate strength of plate with opening under axial compression are presented. It has been found that the ultimate strength of plate ofcase1is much more sensitive to the plate slenderness parameter (β) and opening area ratio (AR) than that of case2. However, for case1, opening position (PR) almost has no effect on the ultimate strength, whereas, regardingcase2, the influence of opening position (PR) depends on the plate slenderness parameter (β). Based on nonlinear regression analysis, three design formulae are not only developed butalso approved reasonably for the practical engineering design.
Abstract
Unstiffened plates are integral part of all kinds of structures such as ship and offshore oil platforms. Openings are unavoidable and absolutely reduce the ultimate strength of structures. In this study, the finite element analysis package, ABAQUS, is used to analyze the behavior of unstiffened plate with rectangular opening. The rectan¬gular opening form is divided into two cases. In case1, opening depth is constant, but opening width is varied. Mean¬while, in case2 opening width is fixed and opening depth is varied. Besides, for the two different form opening, the effect of plate slenderness parameter (β), opening area ratio (AR) and opening position ratio (PR) on the ultimate strength of plate with opening under axial compression are presented. It has been found that the ultimate strength of plate ofcase1is much more sensitive to the plate slenderness parameter (β) and opening area ratio (AR) than that of case2. However, for case1, opening position (PR) almost has no effect on the ultimate strength, whereas, regardingcase2, the influence of opening position (PR) depends on the plate slenderness parameter (β). Based on nonlinear regression analysis, three design formulae are not only developed butalso approved reasonably for the practical engineering design.
참고문헌 (15)
- Tests of unstiffened elements under combined compression and bending, "Bambach, M.R. BE", University of Sydney, ~, pp.Research Report No R818 (2002)
- Cui, W.C., "Effects of welding distortions and residual stresses on the ultimate strength of long rectangular plates under uniaxial compression", Marine Structures, 11, pp.251~269 (1998)
- Jwalamalini, R., "Stability of initially stressed square plates with square openings", Marine Structures, 5(1), pp.71~84 (1992)
- Khaled, M. El-S., "Elasto-plastic buckling of perforated plates under uniaxial com-pression", Thin-Walled Structures, 42(8), pp.1083~1101 (2004)
- Kumar, M. Suneel, "Ultimate strength of square plate with rec-tangular opening under axial compression", Journal of Naval Architecture and Marine Engineering, 4(1), pp.15~26 (2007)
- Madasamy, C.M., "Ayalysis of plated structures with rectangular cutouts and internal supports using the spline finite strip method", Computers and Structures, 52(2), pp.277~286 (1994)
- Mohtaram, Y.F., "Experimental and numerical investigation of buck-ling in rectangular steel plates with groove-shape cut out", Journal of Zhejiang University SCIENCE A, 13(6), pp.469~480 (2011)
- Motok, M.D., "Stress concentration on the contour of a plate opening an arbitrary corner radius of curvature", Marine Structures, 10(1), pp.1~12 (1997)
- Narayanan, R., "Ultimate capacity of uniaxial compressed perforated plates", Thin-Walled Structures, 2(3), pp.241~264 (1984)
- Narayanan, R., "Ultimate capacity of plates containing holes under linearly varying edge displace-ments", Computers and Structures, 21(4), pp.841~849 (1985)
- Paik, J.K., "An analytical method for the ultimate compressive strength and effect-tive plating of stiffened panels", Journal of Constructional Steel Research, 49(1), pp.43~68 (1999)
- Paik, J.K., "Advanced ultimate strength formulations for ship plating under com-bined biaxial compression", tension, edge shear, and lateral pressure loads, 2001, pp.38(1), 153~164
- Roberts, T.M., "Strength of perforated plates subjected to in-plane loading", Thin-Walled Structures, 2(2), pp.153~164 (1984)
- Shanmugam, N.E., "Design formula for axially compressed perforated plates", Thin-Walled Structures, 34(1), pp.1~20 (1999)
- Toulios, M., "The effect of aspect ratio on the elasto-plastic response of stiffened plates loaded in uniaxial edge compression", Computers and Structures, 80(14), pp.1317~1328 (2002)