CFD를 이용한 나선형 튜브 열교환기에서 강제대류의 열유동특성에 관한 연구
A Study on Heat Flow Characteristics of Forced Convection in a Helical Tube Heat Exchanger using CFD
2
조회
0
다운로드
7
인용
0
참고문헌
키워드
초록
In this study, the CFD analysis was performed by changing the geometry of coil-tube diameter ratio, coil winding number, coil pitch, and cross section of the tube to investigate the heat flow characteristics of forced convection in a helical coil-tube heat exchanger using RSM (Reynolds Stress Model). As a result, thesecondary flow was developed in the tube caused by the influence of centrifugal force. It improved the heat transfer on the outer side of the tube, but on the inner side was not performed well. And the temperature rose locally in the tube region. Also the pressure drop in the tube was proportional to the diameter ratio of the coil-tube and the inlet velocity, and it was found that pressure drop and friction factor were inversely proportional. When the coil winding number and coil pitch were increased, it affected heat transfer in the low speed range of 0.1 ~ 0.2 m/s, but did not affect the flow condition after this range.
Abstract
In this study, the CFD analysis was performed by changing the geometry of coil-tube diameter ratio, coil winding number, coil pitch, and cross section of the tube to investigate the heat flow characteristics of forced convection in a helical coil-tube heat exchanger using RSM (Reynolds Stress Model). As a result, thesecondary flow was developed in the tube caused by the influence of centrifugal force. It improved the heat transfer on the outer side of the tube, but on the inner side was not performed well. And the temperature rose locally in the tube region. Also the pressure drop in the tube was proportional to the diameter ratio of the coil-tube and the inlet velocity, and it was found that pressure drop and friction factor were inversely proportional. When the coil winding number and coil pitch were increased, it affected heat transfer in the low speed range of 0.1 ~ 0.2 m/s, but did not affect the flow condition after this range.
참고문헌 (10)
- W. R. Dean, "Note on the motion of fluid in a curved pipe", Philosophical Magazine, 4(20), pp.208~223 (1927)
- R. A. Seban, "Heat transfer in tube coils with laminar and turbulent flow", International Journal of Heat and Mass Transfer, 6(5), pp.387~395 (1963)[DOI]
- J. S. Jakakumar, "Heat Exchangers - Basic Design Application", pp.311~342 (2012), InTech
- P. Jhunjhunwala, "CFD analysis of helically coiled tube for compact heat exchangers", Master's, pp.2013
- S. Ali, "Pressure drop correlations for flow through regular helical coil tubes", Fluid Dynamic Research, 28(4), pp.295~310 (2001)[DOI]
- M. H. Seyyedvalilu, "The effect of Geometrical parameters on heat transfer and hydro dynamical characteristics of helical exchangers", IJMEC, 4(1), pp.35~46 (2015)[DOI]
- S. W. Kim, "Numerical simulation of flows and heat transfer characteristics in spiral tube exchanger", SAREK Summer Conference Proceeding, pp.1169~1176 (1999)
- 윤동혁, "나선형 튜브내의 난류 열전달에 대한 수치적 연구", 대한기계학회논문집 B, 36(8), pp.783~789 (2012), 대한기계학회[DOI]
- 곽승현, "열교환기의 나선형 관내 난류유동 수치해석", 한국마린엔지니어링학회지, 37(8), pp.905~910 (2013), 한국마린엔지니어링학회[DOI]
- 진정정, "각도형상에 따른 정사각형 곡관에서 출구면 및 하류직관거리의 속도분포특성에 관한 연구", 한국기계기술학회지, 18(3), pp.382~390 (2016), 한국기계기술학회[DOI]