전기차의 충전에 사용되는 플라스틱 플러그의 변형 개선에 관한 연구
A Study on Deformation Improvement of Plastic Charging Plug for Electric Car
2
조회
0
다운로드
7
인용
0
참고문헌
키워드
초록
Excellent plastic moldings is possible through optimization of many molding parameters. In particular, the deformation of a plastic part is affected by various factors during molding. Therefore, it is very important to select the optimum molding conditions that minimize the deformation of the molded part. Experimental design is used to select optimal molding conditions. In this study, the molding conditions were selected to minimize the deformation of the electric plastic plug of the electric vehicle using the Taguchi method in the experimental design method. Using the Taguchi Method, we found that the deformation of the plug moldings was reduced by about 7.2% compared to before optimization.
Abstract
Excellent plastic moldings is possible through optimization of many molding parameters. In particular, the deformation of a plastic part is affected by various factors during molding. Therefore, it is very important to select the optimum molding conditions that minimize the deformation of the molded part. Experimental design is used to select optimal molding conditions. In this study, the molding conditions were selected to minimize the deformation of the electric plastic plug of the electric vehicle using the Taguchi method in the experimental design method. Using the Taguchi Method, we found that the deformation of the plug moldings was reduced by about 7.2% compared to before optimization.
참고문헌 (10)
- 한성렬, "수치해석을 이용한 토글식 100톤 사출성형기의 중량 개선에 관한 연구", 한국산학기술학회논문지, 14(10), pp.4713~4718 (2013), 한국산학기술학회[DOI]
- 한성렬, "형상 적응형 냉각채널 적용을 통한 카메라용 플라스틱 렌즈 후드의 변형 개선", 한국기계기술학회지, 21(1), pp.133~139 (2019), 한국기계기술학회[DOI]
- 김우태, "유전체 방전 챔버의 출구 압력 균일성을 위한 다구찌 기법 기반의 설계 변수 최적화", 한국기계기술학회지, 18(1), pp.11~17 (2016), 한국기계기술학회[DOI]
- 한성렬, "자동차 스티어링 휠에 조립되는 플라스틱 베젤의 변형 최적화에 관한 연구", 한국기계가공학회지, 16(5), pp.105~112 (2017), 한국기계가공학회[DOI]
- 김두태, "휨방지를 위한 CAE와 역보정을 이용한 Door Module PNL설계에 관한 연구", Design & Manufacturing, 12(2), pp.27~33 (2018), 한국금형공학회[DOI]
- S. R. Han, "Development of Plastic Passenger Air Bag(PAB)Housing for replacing the Steel PAB Housing and Reducing the Automobile Weight", Journal of the Brazilian Society of Mechanical Sciences and Engineering, 40(4), pp.224~ (2018)
- 이호상, "사출성형 조건이 디스크의 복굴절에 미치는 영향", 한국기계가공학회지, 9(5), pp.28~33 (2010), 한국기계가공학회
- 송재춘, "대형 TV의 플라스틱 후면 커버 성형시의 형체력 절감 방안 연구", Design & Manufacturing, 13(1), pp.36~41 (2019), 한국금형공학회[DOI]
- 한성렬, "Development of the plastic culture container to improve light transmission and stacking possibility", Journal of Mechanical Science and Technology, 31(9), pp.4395~4403 (2017), 대한기계학회
- 유영길, "필름 인서트 사출성형 평판의 휨 변형에 관한 실험적 연구", 소성∙가공, 21(1), pp.30~35 (2012), 한국소성∙가공학회