여유자유도 로봇 매니퓰레이터를 위한 동적제어시스템
A Dynamic Control System for Redundant Robot Manipulator
2
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
This paper deals with the dynamic control of redundant robot manipulator. Traditionally, the kinematic control schemes for redundant robot manipulator were developed from the point of speed and used under the assumption that the dynamic control of manipulator is perfect. However, in reality, the precise control of redundant robot manipulator is very difficult due to their dynamics. Therefore, the kinematic controllers for redundant robot manipulator were employed in the acceleration dimension and may be combined with the computed torque method to achieve the accurate control performance. But their control performance is limited by the accuracy of the manipulator parameters such as the link mass, length, moment of inertia and varying payload. Hence in this paper, the proportional and derivative control gains of the computed torque controller are optimized by the genetic algorithm on the typical payloads, and the neural network is applied to obtain the proper control gains for arbitrary loads. The simulation results show that the proposed control method has better performance than the conventional control method for redundant robot manipulator.
Abstract
This paper deals with the dynamic control of redundant robot manipulator. Traditionally, the kinematic control schemes for redundant robot manipulator were developed from the point of speed and used under the assumption that the dynamic control of manipulator is perfect. However, in reality, the precise control of redundant robot manipulator is very difficult due to their dynamics. Therefore, the kinematic controllers for redundant robot manipulator were employed in the acceleration dimension and may be combined with the computed torque method to achieve the accurate control performance. But their control performance is limited by the accuracy of the manipulator parameters such as the link mass, length, moment of inertia and varying payload. Hence in this paper, the proportional and derivative control gains of the computed torque controller are optimized by the genetic algorithm on the typical payloads, and the neural network is applied to obtain the proper control gains for arbitrary loads. The simulation results show that the proposed control method has better performance than the conventional control method for redundant robot manipulator.
참고문헌 (13)
- R. M. Murray, "A Mathematical Introduction to Robotic Manipulation" (1994), CRC Press
- J. J. Craig, "Introduction to Robotics: Mechanics and Control" (2005), Pearson Education, Inc
- L. Sciavicco, "Modelling and Control of Robot Manipulators" (2000), Springer-Verlag
- Y. Nakamura, "Advanced Robotics: Redundancy and Optimization" (1991), Addison-Wesley
- H. Seraji, "Task options for redundancy resolution using configuration control", 30th IEEE Conf. on Decision and Control, pp.2793~2798 (1991)
- R. Colbaugh, "Obstacle avoidance of redundant robots using configuration control", Int. Journal of Robotics Research, 6, pp.721~744 (1989)
- J. Wang, "Inverse kinematics and control of a 7-dof redundant manipulator based on the closed-loop algorithm", International Journal of Advanced Robotic System, 7(4), pp.1~7 (2010)
- Q. Tang, "Task-priority redundancy resolution on acceleration level for underwater vehicle-manipulator system", International Journal of Advanced Robotic System, 14(4), pp.1~9 (2017)
- F. Flacco, "Control of redundant robots under hard joint constraints : saturation in the null space", IEEE Transaction on Robotics, 31(3), pp.637~654 (2015)
- F. L. Lewis, "Robot Manipulator Control: Theory and Practice" (2004), Marcel Dekker, Inc
- Ullah, M. I., "Modeling and computed torque control of a 6 degree of freedom robotic arm", Robotics and Emerging Allied Technologies in Engineering (iCREATE), pp.133~138 (2014)
- 황시랑, "유전알고리즘을 이용한 로봇 매니퓰레이터의 동적제어기 설계", 한국기계기술학회지, 21(2), pp.195~205 (2019), 한국기계기술학회[DOI]
- T. Ozaki, "Trajectory control of robotic manipulator using neural networks", IEEE Transactions on Industrial Electronics, 38(3), pp.195~202 (1991)