필렛 접합부를 갖는 알루미늄 합금 압출재의 마찰교반용접에 관한 연구
A Study on Friction Stir Welding of Extruded Aluminum Alloy with Fillet Joint
0
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
In this study, experiments and simulations were performed for fillet joint friction stir welding according to tool shape and welding conditions. Conventional butt friction stir welding has good weldability because heat is generated by friction with the bottom of the tool shoulder. However, in the case of fillet friction stir welding, the frictional heat is not sufficiently generated at the bottom of the tool shoulder due to the shape of the tool and the shape of the joint. Therefore, it is important to sufficiently generate frictional heat by slowing the welding speed as compared to butt welding. In this study, experiments and simulations were carried out on an aluminum battery housing made by friction stir welding an extruded material with a fillet joint. The temperature of the structure was measured using a thermocouple during welding, and the heat source was calculated through correlation analysis. Thermal elasto-plastic analysis of the structure was carried out using the calculated heat source and geometric boundary conditions. It is confirmed that the experimental results and the simulation results are well matched. Based on the results of the study, the deformation of the structure can be calculated through simulation even if the tool shape and welding process conditions change.
Abstract
In this study, experiments and simulations were performed for fillet joint friction stir welding according to tool shape and welding conditions. Conventional butt friction stir welding has good weldability because heat is generated by friction with the bottom of the tool shoulder. However, in the case of fillet friction stir welding, the frictional heat is not sufficiently generated at the bottom of the tool shoulder due to the shape of the tool and the shape of the joint. Therefore, it is important to sufficiently generate frictional heat by slowing the welding speed as compared to butt welding. In this study, experiments and simulations were carried out on an aluminum battery housing made by friction stir welding an extruded material with a fillet joint. The temperature of the structure was measured using a thermocouple during welding, and the heat source was calculated through correlation analysis. Thermal elasto-plastic analysis of the structure was carried out using the calculated heat source and geometric boundary conditions. It is confirmed that the experimental results and the simulation results are well matched. Based on the results of the study, the deformation of the structure can be calculated through simulation even if the tool shape and welding process conditions change.
참고문헌 (12)
- Shankar S., "Joint strength evaluation of friction stir welded Al-Cu dissimilar alloys", Measurement, 146, pp.892~902 (2019)
- Meyghani B., "A Comparison Between the Flat and the Curved Friction Stir Welding(FSW)hermomechanical Behaviour", Archives of Computational Methods in Engineering, pp.1~14 (2019)
- Buffa G., "A new friction stir welding based technique for corner Fillet joints : experimental and numerical study", International Journal of Material Forming, 3, pp.1039~1042 (2010)
- Sabry I., "Friction Stir Welding of T-Joints : Experimental and Statistical Analysis", Journal of Manufacturing and Materials Processing, 3, pp.1~23 (2019)
- Salloomi K. N., "Fully coupled thermomechanical simulation of friction stir welding of aluminum 6061-T6 alloy T-joint", Journal of Manufacturing Processes, 45, pp.746~754 (2019)
- Setiawan W., "Varied Corner Joint Design Alumuinum 6061 using Friction Stir Welding", IOP Conference Series: Materials Science and Engineering, 494, pp.1~17 (2019)
- 김영곤, "자동차용 고강도강의 마찰교반접합특성에 미치는 접합 변수의 영향", 한국기계기술학회지, 17(2), pp.267~272 (2015), 한국기계기술학회[DOI]
- 김영곤, "알루미늄 다이캐스팅 합금의 마찰교반접합특성", 한국기계기술학회지, 16(3), pp.1463~1467 (2014), 한국기계기술학회[DOI]
- Reynolds A. P., "Utility of relatively simple models for understanding process parameter effects on FSW", Materials Science Forum, pp.2959~2964 (2003)
- Kang S. W., "Welding Deformation Analysis, Using an Inherent Strain Method for Friction Stir Welded Electric Vehicle Aluminum Battery Housing, Considering Productivity", Applied Sciences, 9, pp.3848~ (2019)
- Naterer G., F., "Advanced Heat Transfer" (2018), CRC Press
- Hyoe T., "Friction Stir Welding and Processing II", TMS Symposium Proceedings (2003), TMS