WAAM에서 내각의 크기가 비드 높이에 미치는 영향
The influence of the interior angle size on the bead height in WAAM
3
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
WAAM(Wire Arc Additive Manufacturing) has gained attention as an innovative technology in small-batch, multi-product production due to its advantages of low production costs, rapid build rates, and design flexibility. However, challenges such as relatively low geometric accuracy, surface finish defects, residual stresses, and distortion due to high heat input persist and require improvement. This study analyzes the influence of deposition path angles on deposition performance in the WAAM process. Experiments were conducted using stainless steel (STS309MoL) wire, known for its excellent heat resistance and corrosion resistance due to its relatively high ferrite content within the austenitic structure. To mitigate residual stresses and distortion caused by high heat input, the CMT(Cold Metal Transfer) process was employed for five layers of deposition. Five different deposition path angles were selected as process variables, and the impact of deposition path angles on deposition performance was evaluated based on experimental results.
Abstract
WAAM(Wire Arc Additive Manufacturing) has gained attention as an innovative technology in small-batch, multi-product production due to its advantages of low production costs, rapid build rates, and design flexibility. However, challenges such as relatively low geometric accuracy, surface finish defects, residual stresses, and distortion due to high heat input persist and require improvement. This study analyzes the influence of deposition path angles on deposition performance in the WAAM process. Experiments were conducted using stainless steel (STS309MoL) wire, known for its excellent heat resistance and corrosion resistance due to its relatively high ferrite content within the austenitic structure. To mitigate residual stresses and distortion caused by high heat input, the CMT(Cold Metal Transfer) process was employed for five layers of deposition. Five different deposition path angles were selected as process variables, and the impact of deposition path angles on deposition performance was evaluated based on experimental results.
참고문헌 (14)
- Y. J. Kim, "A Study on the Additive Manufacturing Process using Copper Wire Nylon Composite Filaments", Journal of the Korean Society of Manufacturing Process Engineers, 21(5), pp.1~8 (2022)
- W. Bintao, "Arc Welding Processes for Additive Manufacturing : A Review", Journal of Manufacturing Processes, 35, pp.127~139 (2018)
- T. A. Rodrigues, "Current Status and Perspectives on Wire and Arc Additive Manufacturing(WAAM)", Materials, 12(7), pp.1121~ (2019)
- J. H. Lim, "Study on Characteristics of V-type Butt Welding Using GMAW Depending on Variations in Improvement Angle of Welding Sections", Journal of the Korean Society of Mechanical Technology, 15(4), pp.505~509 (2013)
- J. H. Lee, "A Study on the Optimization of DED Additive Manufacturing Condition and Path for Repairing Aero Parts", Journal of the Korean Society of Mechanical Technology, 24(5), pp.942~947 (2022)
- S. Y. Park, "Solidification Cracking Susceptibility of the Weld Metal of Additively Manufactured 316L Stainless Steel", Journal of Welding and Joining, 39(1), pp.45~50 (2021)
- H. Hwang, "The Effect of EP", EN Cycle Ratio on the Deposition Characteristics of Al 5183 Aluminum Alloys Fabricated by Variable Polarity WAAM, 2020, pp.38(2), 180~186
- P. A. Colegrove, "High Pressure Interpass Rolling of Wire+Arc Additively Manufactured Titanium Components", Advanced Materials Research, 996, pp.694~700 (2014)
- Y. Fu, ""Investigation of mechanical properties for hybrid deposition and micro-rolling of bainite steel :", Journal of Materials Processing Technology, 250, pp.220~227 (2017)
- J. S. Kim, "Analysis of Mechanical Properties on Ni-Al-Bronze Block Deposited by WAAM(wire arc additive manufacturing)", Journal of the Korean Society of Mechanical Technology, 22(5), pp.959~964 (2020)
- X. Fang, "Correlations between Microstructure characteristics and mechanical properties in 5183 aluminium alloy fabricated by wire-arc additive manufacturing with different arc modes", Materials, 11(11), pp.2075~ (2018)
- T. H. Lee, "Parametric Study of STS 316L Deposition with Arc and Wire Additive Manufacturing", Journal of Welding and Joining, 36(3), pp.23~30 (2018)
- Y. H. Hwang, "Development of Variable Rolling Pressure Device for Bead-Shape Accuracy and Mechanical Property Enhancement in WAAM", Journal of the Korean Society of Manufacturing Process Engineers, 21(8), pp.66~71 (2022)
- J. S. Kim, "A Study on the Bead Geometry Characteristics and Deposition Efficiency of AL5053 Lamination using a WAAM", Journal of the Korean Society of Mechanical Technology, 22(5), pp.821~826 (2020)