차량 라이트 가이드용 STAVAX 금형 가공 시 절삭조건 변화에 따른 표면 거칠기 분석에 대한 연구
A Study on the Surface Roughness Analysis by Cutting Condition in Machining of STAVAX mold for Vehicle Light Guide
6
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
Recently, halogen lamps for vehicle exterior lamp systems are being replaced by LEDs (Light Emitting Diode) in consideration of miniaturization, power consumption, life, luminance, and eco-friendliness. Due to regulations on the amount of light required, luminance, light uniformity, and glare prevention, it is required to develop a light guide for controlling a light source of an LED lamp for a vehicle. For the development of the light guides, the development of machining technology that can cut micro patterns of hundreds of micrometers scale into surface roughness of tens of nanometers scale must be preceded. In this study, the effect of variations in cutting conditions on surface roughness was analyzed through experiments. The micro patterns was manufactured by cutting into STAVAX material, and the surface of the micro patterns was super-finished using a ball-shaped PCD (polycrystalline diamond) tool without flutes. In experiments, the cutting conditions of the super-finishing process were varied, and the varied cutting conditions were feed rate, radial depth of cut, and spindle speed.
Abstract
Recently, halogen lamps for vehicle exterior lamp systems are being replaced by LEDs (Light Emitting Diode) in consideration of miniaturization, power consumption, life, luminance, and eco-friendliness. Due to regulations on the amount of light required, luminance, light uniformity, and glare prevention, it is required to develop a light guide for controlling a light source of an LED lamp for a vehicle. For the development of the light guides, the development of machining technology that can cut micro patterns of hundreds of micrometers scale into surface roughness of tens of nanometers scale must be preceded. In this study, the effect of variations in cutting conditions on surface roughness was analyzed through experiments. The micro patterns was manufactured by cutting into STAVAX material, and the surface of the micro patterns was super-finished using a ball-shaped PCD (polycrystalline diamond) tool without flutes. In experiments, the cutting conditions of the super-finishing process were varied, and the varied cutting conditions were feed rate, radial depth of cut, and spindle speed.
참고문헌 (15)
- An Analysis of the Technology Market for Development of LED Head lamps for Vehicles, "D. W. Lee", Korea Institute of Science and Technology Information, 5~47 (2013)
- 이이선, "세라믹공구를 이용한 금형강(STD11)의 선삭가공 시 가공 조건 결정 및 표면 거칠기 예측", 한국기계기술학회지, 14(4), pp.11~17 (2012), 한국기계기술학회[DOI]
- R. Kurniawan, "Surface roughness of two-frequency elliptical vibration texturing(TFEVT)method for micro-dimple pattern process", International journal of machine tools & manufacture, 116, pp.77~95 (2017)
- 황성국, "BN 첨가된 AISI P20 금형강의 밀링 가공에서 공구 마모와 표면거칠기 특성에 관한 연구", 한국기계기술학회지, 20(4), pp.420~426 (2018), 한국기계기술학회[DOI]
- 정성택, "단결정 다이아몬드공구 제작 기술을 통한 초정밀 미세패턴 가공 연구", Design & Manufacturing, 14(3), pp.63~70 (2020), 한국금형공학회[DOI]
- 조철용, "볼 엔드밀 헬릭스 각에 따른 절삭 특성", 한국정밀공학회지, 31(5), pp.395~401 (2014), 한국정밀공학회
- S. Y. Lee, "Effects of Cutting Conditions on Surface Roughness in Turning", Journal of the Korean Society for Precision Engineering, 18(8), pp.139~149 (2001)
- 심민섭, "미세정밀밀링 가공을 위한 검사시편의 가공조건에 따른 표면거칠기에 대한 영향 분석", 한국정밀공학회지, 32(1), pp.49~55 (2015), 한국정밀공학회
- W. T. Huang, "A combined minimum quantity lubrication and MWCNT cutting fluid approach for SKD 11 end milling", Int J Adv Manuf Technol, 84, pp.1697~1704 (2016)
- 정지훈, "Inconel 718의 평엔드밀링가공에서 가공성평가에 관한 연구", 한국생산제조학회지, 21(6), pp.982~987 (2012), 한국생산제조학회[DOI]
- T. K. choi, "The cutting temperature characteristics depending on cutting conditions in turning of Al6061- T6", Proceedings of KSMTE 2010 autumn conference, Korean Society of Manufacturing Technology Engineers, pp.238~240 (2010)
- 홍광표, "MQL 공급시스템을 이용한 플라스틱 금형강 가공 최적화에 관한 연구", 한국기계가공학회지, 16(6), pp.7~14 (2017), 한국기계가공학회[DOI]
- Y. Hwang, "A Study on the Ultraprecision Grinding of STAVAX", Proceedings of KSPE 2010 autumn conference, pp.99~100 (2010), Korean Society for Precision Engineering
- J. H. Jeong, "Contact lenses for STAVAX Mold", Proceedings of KSPE 2013 spring conference, pp.287~288 (2013), Korean Society for Precision Engineering
- 하석재, "마이크로 금형 부품을 위한 마이크로 절삭가공 기술", Design & Manufacturing, 13(1), pp.5~12 (2019), 한국금형공학회[DOI]