박격포 조준 정렬 품질보증 방법에 관한 연구
A Study on the Quality Assurance Method of Mortar's Sight Alignment
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
This study identifies the possibility of alignment discrepancies during mortar firing when using inactive fuzes, which make it impossible to visually observe impact points. To address this issue, we studied a quality assurance method for Sight Alignment after firing. To establish a baseline, we analyzed the pre-firing Sight Alignment and the impact group status during firing for 00 mortars and 000 shells. Based on this analysis, we derived the alignment position information range after firing for 36 mortars, distinguishing between 68% and 95% confidence interval. Finally, considering data characteristics, inspection time requirements, and non-conforming data, we selected the Sight Alignment range after firing based on the 95% confidence interval. This study is expected to contribute to the development of quality assurance methods for munitions by serving as an example of quality assurance in the mass production stage of mortars.
Abstract
This study identifies the possibility of alignment discrepancies during mortar firing when using inactive fuzes, which make it impossible to visually observe impact points. To address this issue, we studied a quality assurance method for Sight Alignment after firing. To establish a baseline, we analyzed the pre-firing Sight Alignment and the impact group status during firing for 00 mortars and 000 shells. Based on this analysis, we derived the alignment position information range after firing for 36 mortars, distinguishing between 68% and 95% confidence interval. Finally, considering data characteristics, inspection time requirements, and non-conforming data, we selected the Sight Alignment range after firing based on the 95% confidence interval. This study is expected to contribute to the development of quality assurance methods for munitions by serving as an example of quality assurance in the mass production stage of mortars.
참고문헌 (10)
- Seokgyun Hong, "Gun Technology Practical Base", pp.16~29 (2012), Bon Design
- Haewoong Hwang, "Effects of Charge or Bullet Weights on the Muzzle Velocity of a Small Rifle", Journal of the KSME, 15(3), pp.270~274 (1975)
- Hyeeun Kim, "The Improvement of Initial Position Algorithm for Self-propelled Mortars according to Kalman Filter Error Covariance", Journal of the Korea Academia-Industrial cooperation Society, 23(12), pp.838~845 (2022)
- Haesung Yu, "Development of Two-Stage Calibration Technique for MEMS", FOG Inertial Navigation System, 2021, pp.27(6), 450~458
- Gyu-Been Jeong, "Deep Learning Based Tank Aiming line Alignment System", Journal of IKEEE, 25(2), pp.285~290 (2021)
- Dongwhi Kim, "Structural Stability Analysis of a Mount in 000mm Self-propelled Mortar", J. Korean Soc. Mech. Technol, 20(6), pp.836~843 (2018)
- Min-Gu Son, "A Study on the Improvement of Power Supply Logic for 000mm Mortar Gunner Display Device", J. Korean Soc. Mech. Technol, 25(5), pp.802~809 (2023)
- Seonghun Kim, "Development of Effective Test Method for Positioning Accuracy of Armed Vehicle Inertial Navigation System", J Korean Soc Qual Manag, 51(4), pp.619~632 (2023)
- Hee-Jeong Lim, "Estimation of the Random Error of Eddy Covariance Data from Two Towers during Daytime", Atmosphere. Korean Meteorological Society, 26(3), pp.483~492 (2016)
- Yun Youg Jung, "Stochastic Simulation based heuristic Solution for Selecting the Optimal Firing Method of Artillery Firearms(Curved fire Weapon System", J. Military Robotics Society, 2(2), pp.13~20 (2023)