Transmission Electron Microscopy Observation of Twin Variant Selection in Austenitic Twinning-Induced Plasticity Steel
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Twinning-induced plasticity (TWIP) steels with the austenite structure containing high manganese exhibit both good strength and excellent formability. Such properties originate from crystallographic slip and mechanical twins produced when the austenite structure is under mechanical stress. There are 12 twin systems, referred to as twin variants, when slip is induced. These twin systems include twin planes and twin directions and play an important role in determining strength and ductility of the material by strongly influencing texture formation of the austenite structure. In the present study, twins produced in a high-Mn TWIP steel as a result of uniaxial tension were observed using a transmission electron microscope; a comparative analysis was performed through interaction energy calculations. Electron diffraction was used to determine the twin system with respect to the uniaxial tension direction in each grain. Both the Schmid factors and interacting energies required for the generation of twins were calculated and subsequently compared with experimental results. This approach demonstrated the possibility of predicting the deformation behavior of the material.
Abstract
Twinning-induced plasticity (TWIP) steels with the austenite structure containing high manganese exhibit both good strength and excellent formability. Such properties originate from crystallographic slip and mechanical twins produced when the austenite structure is under mechanical stress. There are 12 twin systems, referred to as twin variants, when slip is induced. These twin systems include twin planes and twin directions and play an important role in determining strength and ductility of the material by strongly influencing texture formation of the austenite structure. In the present study, twins produced in a high-Mn TWIP steel as a result of uniaxial tension were observed using a transmission electron microscope; a comparative analysis was performed through interaction energy calculations. Electron diffraction was used to determine the twin system with respect to the uniaxial tension direction in each grain. Both the Schmid factors and interacting energies required for the generation of twins were calculated and subsequently compared with experimental results. This approach demonstrated the possibility of predicting the deformation behavior of the material.
참고문헌 (17)
- Ahn T H, "Strain-induced ε-martensite transformation during nanoindentation of high-nitrogen steel", Mat. Sci. Eng. A, 598, pp.56~61 (2014)
- Allain S, "A physical model of the twinning-induced plasticity effect in a high manganese austenitic steel", Mat. Sci. Eng. A, 387, pp.143~147 (2004)
- Barbier D, "Analysis of the tensile behavior of a TWIP steel based on the texture and microstructure evolutions", Mat. Sci. Eng. A, 500, pp.196~206 (2009)
- Frommeyer G, "Supra-ductile and highstrength Manganese-TRIP", TWIP steels for high energy absorption purposes, 2003, pp.43, 438~446
- Godet S, "Use of Schmid factors to select extension twin variants in extruded magnesium alloy tubes", Scripta Mater, 55, pp.1055~1058 (2006)
- Han J H, "Evolution of crystallographic orientations in an aluminum single crystal during tensile deformation", Mat. Sci. Eng. A, 387, pp.60~63 (2004)
- Hong C S, "Grain orientation dependence of deformation twinning in pure Cu subjected to dynamic plastic deformation", Scripta Mater, 61, pp.289~292 (2009)
- Hua D, "Microstructures and mechanical properties of Fe-Mn-(Al, Si)TRIP", TWIP steels, 2006, pp.13, 66~70
- Hull D, "Introduction to Dislocation" (2001), Butterworth-Heinemann
- Idrissi H, "Is there a relationship between the stacking fault character and the activated mode of plasticity of Fe–Mn-based austenitic steels?", Scripta Mater, 60, pp.941~944 (2009)
- Karaman I, "Deformation of single crystal Hadfield steel by twinning and slip", Acta Mater, 48, pp.1345~1359 (2000)
- Lee S H, "Variant selection in mechanically-induced martensitic transformation of metastable austenitic steel", ISIJ Int, 45, pp.1217~1219 (2005)
- Pérez-Prado M T, "Lattice rotation during severe local shear in a fully hardened Al–4% Cu–0. 1% Fe single crystal alloy", Scripta Mater, 54, pp.915~919 (2006)
- Scheriau S, "Influence of grain size on orientation changes during plastic deformation", Mat. Sci. Eng. A, 493, pp.48~52 (2008)
- Ueji R, "Tensile properties and twinning behavior of high manganese austenitic steel with fine-grained structure", Scripta Mater, 59, pp.963~966 (2008)
- Vercammen S, "Cold rolling behaviour of an austenitic Fe–30Mn–3Al–3Si TWIP-steel: the importance of deformation twinning", Acta Mater, 52, pp.2005~2012 (2004)
- Yang P, "Dependence of deformation twinning on grain orientation in a high manganese steel", Scripta Mater, 55, pp.629~631 (2006)