38ft급 HDPE 파워보트 구조해석을 통한 선급별 하중 기준에 대한 비교 고찰
Comparative Study on Load Criteria by Class Based on Structural Analysis of 38ft HDPE Power Boat
0
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
According to the government policy of environmental regulations, interest of ship, which made with High-Density Polyethylene (HDPE) as a low-carbon and eco-friendly material, is growing as a substitute for the existing fishery boat hull materials such as FRP, aluminum, steel etc. However, regulations related to the production of HDPE ship are still quite incomplete. Even there are no regulations related to structural analysis. Therefore, in this study, structural analysis is carried out by applying different design loads for each international classification for 38ft class HDPE power boats, and the results are compared and analyzed. According to this study, although there is a correlation between the based pressure value and the analysis result value of each class regulation, it is not necessarily proportional. Also, This analysis result shows a difference not only depending on the size of design load, but also application range of the load, the pressure adjustment factor and section shape. However, the occurrence point and trend of the maximum stress values were quite consistent. It is hoped that the results of this study will be used when establishing HDPE ship structure analysis procedures and standards in the future.
Abstract
According to the government policy of environmental regulations, interest of ship, which made with High-Density Polyethylene (HDPE) as a low-carbon and eco-friendly material, is growing as a substitute for the existing fishery boat hull materials such as FRP, aluminum, steel etc. However, regulations related to the production of HDPE ship are still quite incomplete. Even there are no regulations related to structural analysis. Therefore, in this study, structural analysis is carried out by applying different design loads for each international classification for 38ft class HDPE power boats, and the results are compared and analyzed. According to this study, although there is a correlation between the based pressure value and the analysis result value of each class regulation, it is not necessarily proportional. Also, This analysis result shows a difference not only depending on the size of design load, but also application range of the load, the pressure adjustment factor and section shape. However, the occurrence point and trend of the maximum stress values were quite consistent. It is hoped that the results of this study will be used when establishing HDPE ship structure analysis procedures and standards in the future.
참고문헌 (10)
- DNV·GL, "DNVGL-ST-0342 Craft", ~ (2016)
- "Small craft – Hull construction and scantlings – Part5 : Design pressures for monohulls, design stresses, scantlings determination", ISO 12215-5, ~ (2012)
- 고대은, "8m급 고속 활주선형 레저보트의 구조강도 평가", 한국산학기술학회논문지, 19(10), pp.418~423 (2018), 한국산학기술학회[DOI]
- Rules for the classification of high speed light craft, "Korean Register", ~ (2022)
- Rules for the classification of steel ships, Annex 3-2 guidance for the direct strength assessment, "Korean Register", ~ (2022)
- Rules and regulations for the Classification of Special Service Craft, "Lloyd’s Register", ~ (2021)
- 오대균, "탄소섬유강화복합재료(CFRP) 레저선박선체설계를 위한 ISO 12215와 국제선급규정 비교분석", 한국해양공학회지, 28(1), pp.77~84 (2014), 한국해양공학회
- 박주신, "38피트급 보급형 고속 카타마란 요트의 구조해석", 한국항해항만학회지, 33(3), pp.167~174 (2009), 한국항해항만학회
- 염재선, "20피트급 파워보트의 구조강도 평가 및 최적화", 대한조선학회 논문집, 53(2), pp.108~114 (2016), 대한조선학회
- 염재선, "티타늄합금 레저보트의 구조설계를 위한 설계하중 비교연구", 한국산학기술학회논문지, 22(2), pp.733~738 (2021), 한국산학기술학회[DOI]