니켈합금 Metal Foam을 적용한 예혼합 버너의 연소특성
Combustion Characteristics of Premixed Combustor using Nickel Based Metal Foam
0
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
A premixed combustion has many advantages including low NOx and CO emission, high thermal efficiency and a small volume of combustor. This study focused on combustion characteristics in a premixed combustion burner using the nickel based metal foam. The results show that the blue flame is found to be very stable at heating load 6,300-25,200 kcal/h by implementing the proper nickel based metal foam and baffle plate. The premixed flame mode is changed into green flame, red flame, blue flame and lift off flame with decreasing equivalence ratio. NOx emission was measured 80 ppm(0% oxygen base) from 0.710 to 0.810 of equivalence ratio and CO emission is 90 ppm(0% oxygen base) under the same equivalence ratio. It is also found that the stable blue flame region in flame stability curve becomes wider with increasing the heat load.
Abstract
A premixed combustion has many advantages including low NOx and CO emission, high thermal efficiency and a small volume of combustor. This study focused on combustion characteristics in a premixed combustion burner using the nickel based metal foam. The results show that the blue flame is found to be very stable at heating load 6,300-25,200 kcal/h by implementing the proper nickel based metal foam and baffle plate. The premixed flame mode is changed into green flame, red flame, blue flame and lift off flame with decreasing equivalence ratio. NOx emission was measured 80 ppm(0% oxygen base) from 0.710 to 0.810 of equivalence ratio and CO emission is 90 ppm(0% oxygen base) under the same equivalence ratio. It is also found that the stable blue flame region in flame stability curve becomes wider with increasing the heat load.
참고문헌 (16)
- Turns, S. R., "An Introduction to Combustion" (2000), McGraw Hill
- D. R. Derek, "Lean Combustion Technology and Control" (2007), Elsevier
- 이필형, "가동조건 변화에 따른 순산소 마일드 연소 형성 연구", 대한기계학회논문집 B, 40(9), pp.577~587 (2016), 대한기계학회
- 정준영, "메탈화이버 버너의 화염구조 및 공해물질 배출 특성", 한국연소학회지, 16(3), pp.27~32 (2011), 한국연소학회
- S. H. Jun, "A study of the combustion characteristics of the air-fuel ratio of bunsen burner gas boiler", M. S., pp.2002
- 조은성, "평판형 예혼합 버너의 다양한 화염면 매질 및 열교환기에 따른 연소 특성", 대한기계학회논문집 B, 35(10), pp.1033~1040 (2011), 대한기계학회
- 양시원, "Perforated Cordierite 재질 버너의 화염 형태 및 안정성 특성", 한국연소학회지, 10(1), pp.7~12 (2005), 한국연소학회
- P. H. Lee, "Formation of Lean Premixed Surface Flame Using Porous Baffle Plate and Flame Holder", J. Therm. Sci. Tech, 8(1), pp.178~189 (2013)
- F. J. Weinberg, "Combustion temperatures : the future", Nature, 233, pp.239~ (1971)
- I. Schoegl, "Superadiabatic combustion in conducting tubes and heat exchangers of finite length", Combust. Flame, 151, pp.142~159 (2007)
- M. K. Drayton, "Syngas production using superadiabatic combustion of ultra-rich methane-air mixtures", Proc. Combust. Inst, 27, pp.1361~1367 (1998)
- P. H. Lee, "Superadiabatic flame for production of hydrogen rich gas from methane", Int. J. Hydrogen Energy, 41, pp.11801~11810 (2016)
- S. S. Hwang, "Combustion and Emission Characteristics of the Surface Flames in Porous Ceramic Burner", J. Korean Soc. Combust, 6(1), pp.29~35 (2001)
- S. H. Lee, "The Combustion Characteristics of Flame Front Stablized in a Porous Burner", M. S., pp.2001
- U. K. Shin, "A Study on the Combustion Phenomena in Porous Ceramic Burner", M. S., pp.1999