바이몰프 압전센서의 진동에너지 수확에 관한 연구
A study of vibration energy harvesting for the bimorph piezoelectric sensor
2
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
Vibration energy harvesting is an attractive technique for potential powering of low power devices such as wireless sensors and portable electronic applications. Most energy generator developed to date are single vibration frequency based, and while some efforts have been made to broaden the frequency range of energy harvester. In this work, The effect of energy harvesting were investigated at various vibration frequencies, vibration beams, vibration point and test masses. The maximum output voltage of the bimorph piezoelectric cantilever was shifted according to vibration point. Vibration frequency with maximum output voltage decreased with the increasing length of vibration beam and increasing test mass. The sample with vibration beam length 0.5 ﾠL generated a peak output voltage of 32 Vr m s and shows a 45 ﾠ% increase in voltage output in comparison to the corresponding original bimorph. It was found that a piezoelectric bimorph has a possibility to be as the energy harvesting cantilever, which is successfully tuned over a vibration frequency range to enable a maximum harvesting energy.
Abstract
Vibration energy harvesting is an attractive technique for potential powering of low power devices such as wireless sensors and portable electronic applications. Most energy generator developed to date are single vibration frequency based, and while some efforts have been made to broaden the frequency range of energy harvester. In this work, The effect of energy harvesting were investigated at various vibration frequencies, vibration beams, vibration point and test masses. The maximum output voltage of the bimorph piezoelectric cantilever was shifted according to vibration point. Vibration frequency with maximum output voltage decreased with the increasing length of vibration beam and increasing test mass. The sample with vibration beam length 0.5 ﾠL generated a peak output voltage of 32 Vr m s and shows a 45 ﾠ% increase in voltage output in comparison to the corresponding original bimorph. It was found that a piezoelectric bimorph has a possibility to be as the energy harvesting cantilever, which is successfully tuned over a vibration frequency range to enable a maximum harvesting energy.
참고문헌 (15)
- Roundy,S, "On the effectiveness of vibration-based energy harvesting", Journal of Intelligent Material Systems and Structures, 16(10), pp.809~823 (2005)
- Sodano, H. A, "Comparison of piezoelectric energy harvesting devices for recharging batteries", Journal of Intelligent Material Systems and Structures, 16(10), pp.809~823 (2005)
- Ericka, M, "Energy harvesting from vibration using a piezoelectric membrane", Journal de physique, 4(128), pp.187~193 (2005)
- Meninger S, "Vibration-to-electric energy conversion", IEEE Trans. Very Large Scale Integr. (VLSI) Sys, 9, pp.64~76 (2001)
- Despesse G, "High damping electrostatic system for vibration energy scavenging", Joint sOc-EUSAI Conf, pp.1~6 (2005)
- Glynne-Jones P, "An electromagnetic,vibration-powered generator for intelligent sensor systems", Sensors Actuators A, 110, pp.344~349 (2004)
- Saha C. R, "Optimization of an electro magnetic energy harvesting device", IEEE Trans. Mag, 42, pp.3509~3511 (2006)
- Sodano H. A, "A review of power harvesting from vibration using piezoelectric materials", Shock Vib. Dig, 36, pp.197~205 (2004)
- Sodano H. A, "Estimation of electric charge output for piezoelectric energy harvesting", Strain, 40, pp.49~58 (2004)
- Robert B. M, "Energy management of multi-component power harvesting system", SPIE, energy harvesting and scavenging, 4, pp.6928~ (2008)
- Gonzalez, J. L, "Human powered piezoelectric batteries to supply power to wearable electronic devices", Int. J.-Soc. Mater. Eng. Resources, 10, pp.34~40 (2001)
- Lefeuvre, E, "A compraision between several vibratin-powered piezoelectric generators for standalone systems", Sensors and Actuators A-Physical, 126(2), pp.405~416 (2006)
- Shen, D, "The optimal design and analysis of piezoelectric cantilever beams for power generation devices", Mater. Res. Soc. Symp. Proc, 3, pp.888~ (2006)
- Vinod R. C, "A coupled piezoelectric-electromagnetic energy harvesting technique for achieving increased power output through damping matching", Smart Mater. Struct, 18, pp.1~11 (2009)
- 김인성, "Micro Power Generation of a PMN-PZT Triple-morph Cantilever for Electric Harvesting Devices", Journal of the Korean Physical Society, 56(1), pp.370~373 (2010), 한국물리학회