열처리 공정을 이용한 regenerated FBG의 제작
Fabrication of Regenerated Fiber Bragg Grating Using Thermal Annealing
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
In this paper, we manufactured the regenerated FBG by the thermal annealing of seed FBG based on UV irradiation. The writing conditions of regenerated FBGs were investigated in four types of optical fiber. FBGs written in H2-free fiber were erased and not regenerated during the thermal annealing. FBG written in H2 loaded Boron co-doped fiber was erased at the temperature of about 580℃ and regenerated about 590℃ . However, the extinction of regenerated FBG started at the temperature over 900℃ and then FBG disappeared out. FBG written in H2 loaded Ge high doped fiber was erased and regenerated around the temperature of 800℃ and maintained until the end of the thermal annealing. The reflection of the regenerated FBG was decreased about 12 dB and the center wavelength of the regenerated FBG was shifted about 0.7 nm compared with that of the seed FBG. The thermal characteristics of the regenerated FBG were analyzed by reheating from room temperature to 980℃ . As results, the regenerated FBG had survived without a decrease of reflection and the thermal sensitivity was 15 pm℃ .
Abstract
In this paper, we manufactured the regenerated FBG by the thermal annealing of seed FBG based on UV irradiation. The writing conditions of regenerated FBGs were investigated in four types of optical fiber. FBGs written in H2-free fiber were erased and not regenerated during the thermal annealing. FBG written in H2 loaded Boron co-doped fiber was erased at the temperature of about 580℃ and regenerated about 590℃ . However, the extinction of regenerated FBG started at the temperature over 900℃ and then FBG disappeared out. FBG written in H2 loaded Ge high doped fiber was erased and regenerated around the temperature of 800℃ and maintained until the end of the thermal annealing. The reflection of the regenerated FBG was decreased about 12 dB and the center wavelength of the regenerated FBG was shifted about 0.7 nm compared with that of the seed FBG. The thermal characteristics of the regenerated FBG were analyzed by reheating from room temperature to 980℃ . As results, the regenerated FBG had survived without a decrease of reflection and the thermal sensitivity was 15 pm℃ .
참고문헌 (16)
- R. J. Sun, "An integrated FBG sensing system for bridge health monitoring", Proc. of SPIE, 6174, pp.61742Q1~ (2006)
- P. Biswas, "Investigation on packages of fiber Bragg grating for use as embeddable strain sensor in concrete structure", Sensor Actuat. A-Phys, 157, pp.77~83 (2010)
- W. L. Schulz, "Advanced fiber grating strain sensor systems for bridges, structures, and highway", Proc. SPIE, 3325, pp.212~221 (1998)
- G. Wang, "Ship hull structure monitoring using fibre optic sensors", Smart Mater. Struct, 10, pp.472~ (2001)
- A. Cusano, "Experimental modal analysis of an aircraft model wing by embedded fiber Bragg grating sensors", IEEE Sens. J, 6, pp.67~77 (2006)
- K. Schroeder, "A fibre Bragg grating sensor system monitors operational load in a wind turbine rotor blade", Meas. Sci. Technol, 17, pp.1167~1172 (2006)
- A. F. Fernandez, "Fibre Bragg grating temperature sensors for harsh nuclear environments", Conf. of OFS, 1, pp.63~66 (2002)
- W. Ecke, "Fiber optic grating sensors for structural health monitoring at cryogenic temperatures", Proc. of SPIE, 6530, pp.1~8 (2007)
- H. Bartelt, "Single-pulse fiber Bragg gratings and specific coatings for use at elevated temperatures", Appl. Optics, 46, pp.3417~3424 (2007)
- T. Erdogan, "Decay of ultraviolet-induced fiber Bragg gratings", J. Appl. Phys, 76, pp.73~80 (1994)
- N. Groothoff, "Enhanced type IIA gratings for high-temperature operation", Opt. Lett, 29, pp.2360~2362 (2004)
- J. L. Archambault, "High reflectivity and narrow bandwidth fibre gratings written by single excimer pulse", Electron. Lett, 29, pp.28~29 (1993)
- M. Fokine, "Underlying mechanisms, applications, and limitations of chemical composition gratings in silica based fibers", J. Non-Crystal. Solids, 349, pp.98~104 (2004)
- J. H. Seo, "The study of regenerated fiber Bragg grating for high temperature application", Proceeding of the Korean Sensors Society, 23, pp.145~ (2012)
- G. Meltz, "Formation of Bragg gratings in optical fibers by a transverse holographic method", Opt. Lett, 14, pp.823~825 (1989)
- Hill, K.O, "Bragg gratings fabricated in monomode photosensitive optical fiber by UV exposure through a phase mask", Appl. Phys. Lett, 62, pp.1035~1037 (1993)