MEMS 기반의 차량용 휨형 유속센서의 제작 및 특성 연구
Study on the Fabrication and Evaluation of the MEMS Based Curved Beam Air Flowmeter for the Vehicle Applications
1
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
This paper presents the fabrication and evaluation of the novel drag force type air flowmeter using MEMS technologies for the vehicle applications. To obtain the air drag force, the flowmeter utilized the curved beam structure, which was realized by the difference of residual stress between the silicon oxide layer and the silicon nitride layer. The paddle structure was applied for the maximum air drag force, and the dual-beam was adapted to prevent distortion. The basic experiments were performed in the wind tunnel, and the stable outputs were obtained. The device was applied to the internal combustion engine, and the results were compared with the HI-DS output where the convection thermal flowmeter was used as the reference sensor. The results indicated that the comparable resolutions and response times were obtained under the various engine speeds
Abstract
This paper presents the fabrication and evaluation of the novel drag force type air flowmeter using MEMS technologies for the vehicle applications. To obtain the air drag force, the flowmeter utilized the curved beam structure, which was realized by the difference of residual stress between the silicon oxide layer and the silicon nitride layer. The paddle structure was applied for the maximum air drag force, and the dual-beam was adapted to prevent distortion. The basic experiments were performed in the wind tunnel, and the stable outputs were obtained. The device was applied to the internal combustion engine, and the results were compared with the HI-DS output where the convection thermal flowmeter was used as the reference sensor. The results indicated that the comparable resolutions and response times were obtained under the various engine speeds
참고문헌 (23)
- K. A. Small, "Fuel efficiency and motor vehicle travel : The declining rebound effect", J. Energy, 28(1), pp.25~51 (2007)
- S. T. Anderson, "Automobile fuel economy standards : Inpacts, efficiency, and alternatives", J. REEP, 5(1), pp.89~108 (2011)
- X. Wu, "Energy efficiency and economy analysis of a range-extended electric bus in different chinese city driving cycles", IJUNESST, 7(2), pp.83~90 (2014)
- V. Manieniyan, "Experimental analysis of exhaust gas recirculation on DI diesel engine operating with biodiesel", Int. J. Eng. Technol, 3(2), pp.129~135 (2013)
- H. S. Sorathia, "Effect of exhaust gas recirculation(EGR)on nox emission from C. I. engine – A review study", IJAERS, 1(3), pp.223~227 (2012)
- D. Niarchos, "Magnetic MEMS : key issues and some applications", Sens. Actuators A., 109(1-2), pp.166~173 (2003)
- Y. Fu, "TiNi-based thin films in MEMS applications : a review", Sens. Actuators A., 113(2-3), pp.395~408 (2004)
- M. Blaschke, "MEMS gas-sensor array for monitoring the perceived car-cabin air quality", J. IEEE. Sensors, 6(5), pp.1298~1308 (2006)
- D. S. Eddy, "Application of MEMS technology in automotive sensor and actuators", J. IEEE. Sensors, 86(8), pp.1747~1755 (1998)
- W. J. Fleming, "Overview of automotive sensors", J. IEEE. Sensors, 1(4), pp.296~308 (2001)
- 전기자동차 보급의 에너지 수급 영향 분석, "최도영", 에너지경제연구원, 1~6 (2012)
- S. C. Roh, "Sensitivity enhancement of a silicon micro-machined thermal flow sensor", Sens. Actuators A, 128(1), pp.1~6 (2006)
- P. Bruschi, "Effects of gas type on the sensitivity and transition pressure of integrated thermal flow sensors", Sens. Actuators A, 132(1), pp.182~187 (2006)
- C. Sosna, "A temperature compensation circuit for thermal flow sensor operated in constant-temperature-difference mode", IEEE Trans. Instrum. Meas, 59(6), pp.1715~1721 (2010)
- Y. H. Wang, "A MEMS-based air flow sensor with a free-standing micro-cantilever structure", Proc. of IEEE Conf. on Sensors, pp.2389~2401 (2007)
- C. Y. Lee, "Design and characterization of MEMS-based flow-rate and flow-direction microsensor", Microfluid Nanofluid, 6(3), pp.363~371 (2009)
- Q. Zhang, "A self-bended piezoresistive microcantilever flow sensor for low flow rate measurement", Sens. Actuators A, 158(2), pp.273~279 (2010)
- M. Dijkstra, "Artificial sensory hairs based on the flow sensitive receptor hairs of crickets", J. Micromech. Microeng, 15(7), pp.132~138 (2005)
- 최대근, "주름구조를 적용한 저속 유속 센서", 센서학회지, 20(6), pp.393~399 (2011), 한국센서학회
- D. K. Choi, "Design and fabrication of a novel flowmeter with corrugation structure", Microelectron. Eng, 98(1), pp.477~482 (2012)