소재-구조 최적화 기반 다층-복합재료구조 충격흡수성능
Impact Absorption Performance of Multi-layered Composite Structures based on Material-Structure Optimization
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
적층 두께, 면밀도, 질량관성모우멘트는 소재의 구조-역학적 특성을 나타내는 중요한 인자들이다. 본 연구에서는 이와 같은 인자들이 다층-복합재료구조의 내충격 성능에 미치는 영향을 고찰하기 위해 높은 충격자 속도 하에서 탄자한계속도가 최대가 되는 재료-구조 최적화를 수행하였다. 세라믹복합재료, 고무, 알루미늄 그리고 알루미늄 폼으로 구성된 다층-복합재료구조의 최적화를 위해 Florence 모델과 Awerbuch-Bonder 모델을 연계한 통합 모델을 개발하였으며, 구속 조건으로써 적층 두께, 면밀도 질량관성모우멘트를 함께 사용하였다. 결과에서 알 수 있듯이, 제안된 통합 모델을 통해 계산된 탄자한계속도는 유한요소해석에서의 탄자한계속도와 거의 유사함을 확인하였다. 통합 모델을 바탕으로 재료-구조 최적화를 통해 설정된 다층구조는 최적화를 수행하지 않은 다층구조에 비해 약 16.8 %의 탄자한계속도 및 26.7 %의 충격흡수에너지 향상이 나타남을 알 수 있다.
Abstract
Total thickness, areal density and mass moment of inertia of materials are important material factors for structural characteristics. In this work, a material-structural optimization was performed up to the maximum ballistic limit of multi-layered composite structures under high impact velocity followed by the investigation of the influence of these factors on an impact absorption performance. A unified model combined with Florence’s and Awerbuch-Bonder’s models was used in optimizing the multi-layered composite structure consisting of CMC, rubber, aluminum and Al-foam. Total thickness, areal density and mass moment of inertia were used for the optimization constraint. As shown in the results, the ballistic limit determined from a newly developed unified model was closely similar to the finite element analysis. Additionally, the ballistic limit and impact absorption energy obtained by the optimized structure were improved approximately 16.8 % and 26.7 %, respectively comparing with a not optimized multi-layered structure.
참고문헌 (18)
- 안성훈, "전투차량용 세라믹복합재료 복합장갑의 개발추세", 한국정밀공학회지, 22(7), pp.7~18 (2005)
- "“Military Specification Armor,” U. S. Patents, 1984, MIL-A- 62473", ~
- The Analysis of Threat Projectiles for Protection of Light Tactical Vehicle, "Gooch, W.A.", U. S. Army Research Laboratory, ~, pp.ARL-RP-89 (2004)
- Borvik, T., "Effect of Target Thickness in Blunt Projectile Penetration of Weldox 460 E Steel Plate", International Journal of Impact Engineering, 28(4), pp.413~464 (2003)
- Hetherington, J.G., "The Optimization of Two Component Composite Armours", International Journal of Impact Engineering, 12(3), pp.409~414 (1992)
- Wang, B, "On the Optimization of Twocomponent Plates against Ballistic Impact", Journal of Materials Processing Technology, 57(1), pp.141~145 (1996)
- Florence, A.L., "“Interaction of projectile and composite armor, Part II,” Stanford Research Institute, Menlo Park (CA, USA), 1969, AMMRG-CR-69-15", ~ (1969)
- Ben-Dor, G., "Optimization of two-component composite armor against ballistic impact", Composite Structures, 69(1), pp.89~94 (2005)
- Shi, J., "Effect of double constraints on the optimization of two-component armor systems", Composite Structures, 79(3), pp.445~453 (2007)
- Awerbuch, J., "Experimental Investigation of Normal Perforation of Projectiles in Metallic Plates", International Journal of Solid Structures, 10, pp.685~699 (1974)
- Mahfuz, H., "Investigation of highvelocity impact on integral armor using finite element method", International Journal of Impact Engineering, 24(2), pp.203~217 (2000)
- Kim, Y., "Determination of Shock Absorption Characteristics with Florence Scheme in Multi-layered Composite Structures", The 6th Asian- Australasian Conference on Composite Materials, pp.267~270 (2008)
- Lee, M., "Analysis of Ceramic", metal Armour Systems, 2001, pp.25(9), 819~829
- Woodward, R.L., "A Study of Fragmentation in the Ballistic Impact of Ceramics", International Journal of Impact Engineering, 15(5), pp.605~618 (1995)
- Damage Tolerance of Thick-section Composites Subjected to Ballistic Impact, "Fink, B.K.", U. S. Army Research Laboratory, ~, pp.ARL-TR- 2477 (2001)
- Gama, B.A., "Aluminum Foam Integral Armor: A New Dimension in Armor Design", Composite Structures, 52(3), pp.381~395 (2001)
- Rosenberg, Z., "A numerical study of the cavity expansion process and its application to long-rod penetration mechanics", International Journal of Impact Engineering, 35, pp.147~154 (2008)