레이저 및 플라즈마 표면처리에 따른 이종소재 접합특성평가
Evaluation of Bonding Performance of Hybrid Materials According to Laser and Plasma Surface Treatment
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
최근 경량 소재에 대한 수요 증가로 기존 금속과 복합재간 접합 관심이 지대하다. 리벳팅과 같은 볼트 체결인 기계적 결합의 경우 응력 집중, 균열 및 박리가 발생함에 따라 접착제를 사용한 화학적 결합이 주목받고 있다. 본 논문에서는 접착제의 접착강도 향상을 위해 레이저 및 플라즈마 표면처리를 진행하였으며, 이에 대한 접착특성을 평가하고자 한다. 접착강도 실험을 위해 흔히 자동차용 소재로 사용되는 탄소섬유강화플라스틱(CFRP), CR340(Steel) 과 Al6061(Aluminum)을 실험 소재로 선정해 레이저 및 플라즈마 표면처리를 진행 후 단축전단강도를 측정하였다. 플라즈마 표면처리 후 CFRP-CR340 및 CFRP-Al6061 이종소재 시편에서 각각 접착강도가 7.3% 및 39.2% 향상되었다. CR340-Al6061 시편은 레이저 표면처리에서 기준 시편대비 56.2% 증가하였다. 플라즈마 표면처리 후 표면자유에너지(SFE)가 향상되었는데 이는 화학반응 메커니즘을 통해 손상을 최소화해 접착강도 향상을 나타낸 것으로 사료된다. 레이저 표면처리는 물리적 표면처리로 거친 접합 표면 생성으로 인해 mechanical interlocking 효과로 인해 접착 강도가 향상된 것으로 사료된다. 본 연구를 토대로 실제 구조물 파손의 대표적인 원인인 피로파손을 예방하기 위해 장기 피로시험을 진행 할 예정이다.
Abstract
Recently, as demand for high-strength, lightweight materials has increased, there has been great interest in joining with metals. In the case of mechanical bonding, such as bolting and riveting, chemical bonding using adhesives is attracting attention as stress concentration, cracks, and peeling occur. In this paper, surface treatment was performed to improve the adhesive strength, and the change in adhesive strength was analyzed. For the adhesive strength test were conducted with Carbon Fiber Reinforced Plastic(CFRP), CR340(Steel), and Al6061(Aluminum), and laser and plasma surface treatment were used. After plasma surface treatment, the adhesive strength improved by 7.3% and 39.2% in CFRP-CR340 and CFRP-Al6061, respectively. CR340-Al6061 was improved by 56.2% in laser surface treatment. Surface free energy(SFE) was measured by contact angle after plasma treatment, and it is thought that the adhesion strength was improved by minimizing damage through a chemical reaction mechanism. For laser surface treatment, it is thought that creates a rough bonding surface and improves adhesive strength due to the mechanical interlocking effect. Therefore, surface treatment is effect to improve adhesive strength, and based on this paper, the long-term fatigue test will be conducted to prevent fatigue failure, which is a representative cause of actual structural damage.
참고문헌 (20)
- 손동일, "복합소재 사출인서트 알루미늄 바 카울크로스멤버 표면처리 특성에 따른 접합강도 분석 연구", Composites Research, 33(6), pp.360~364 (2020), 한국복합재료학회
- 이민식, "Al5052", CFRP 복합소재의 표면특성이 접착성과 기계적특성에 미치는 영향, 2013, pp.26(5), 295~302[DOI]
- 김지훈, "탄소 섬유 강화 플라스틱과 금속의 접합에서 표면 패턴에 따른 접합 강도 영향", 한국생산제조학회지, 26(4), pp.430~435 (2017), 한국생산제조학회[DOI]
- Zhan, X., "Effect of Infrared Laser Surface Treatment on the Microstructure and Properties of Adhesively CFRP Bonded Joints", Optics and Laser Technology, 106(9), pp.398~409 (2018)
- 김무선, "물리적 표면처리 기법에 따른 복합소재 및 알루미늄간 접합특성 연구", 한국산학기술학회논문지, 21(11), pp.334~339 (2020), 한국산학기술학회[DOI]
- Al-Zubaidy, H., "Experimental Investigation of Bond Characteristics between CFRP Fabrics and Steel Plate Joints under Impact Tensile Loads", Polymer Composite, 94(2), pp.510~518 (2019)
- Çoban, O, "Laser Surface Treatment of CFRP Composites for a Better Adhesive Bonding Owing to the Mechanical Interlocking Mechanism", Composite Structures, 40(9), pp.3611~3622 (2012)
- Sundriyal, P., "Plasmaassisted Surface Alteration of Industrial Polymers for Improved Adhesive Bonding", International Journal of Adhesion and Adhesives, 101(6), pp.102626~ (2020)
- Martínez-Landeros, V. H., "Studies on the Influence of Surface Treamtne Type, in the Effectiveness of Structural Adhesive Bonding, for Carbon Fiver Reinforced Composites", Journal of Manufacturing Process, 39(3), pp.160~166 (2019)
- Harder, S., "Effect of Infrared Laser Surface Treatment on the Morphology and Adhesive Properties of Scarfed CFRP Surface", Composite Part A : Applied Science and Manufacturing, 121(6), pp.299~307 (2019)
- Matthews, F. L., "A Review of the Strength of Joints in Fibre-reinforced Plastics. Part 2. Adhesively Bonded Joints", Composites, 13(1), pp.29~37 (1982)
- He, X., "A Review of Finite Element Analysis of Adhesively Bonded Joints", International Journal of Adhesion and Adhesives, 31(4), pp.248~264 (2011)
- Gude, M. R., "Hydrothermal Ageing of Adhesive Joints with Nanoreinforced Adhesives and Different Surface Treatments of Carbon Fibre", epoxy Substrates, 2013, pp.40(1), 179~187
- Liu, L., "Effect of Laser Surface Treatment on Surface and Bonding Properties of Carbon Fiber Reinforced Composites", International Journal of Material Forming, 13(1), pp.885~895 (2020)
- Sun, C., "Effect of Atmospheric Pressure Plasma Treatment on Adhesive Bonding of Carbon Fiber Reinforced Polymer", Polymers, 11(1), pp.1~19 (2019)
- Adhesive Technology, "Assessment of Surface Preparation for the Bonding", pp.2019, Rudawska, A.
- Zhan, X., "Effect of Infrared Laser Surface Treatment on the Microstructure and Properties of Adhesively CFRP Bonded Joints", Optics and Laser Technology, 106(9), pp.398~409 (2018)
- Bionghi, R., "Correction between Bond Strength and Surface Free Energy Parameters of Asphalt Binder-aggregate System", Construction and Building Materials, 303(38), pp.398~409 (2021)
- Wetzel, M., "Sensitivity of Double Cantilever Beam Test to Surface Contamination and Surface Pretreatment", International Journal of Adhesion and Adhesives, 46(7), pp.114~121 (2013)
- Leone, C., "Investigation of CFRP Laser Milling Using a 30W Q-switched Yb : YAG Fiber Laser : Effect of Process Parameters on Removal Mechanisms and HAZ Formation", Composite Part A : Applied Science and Manufacturing, 55(12), pp.129~142 (2013)