Fabrication of FeCuNi alloy by mechanical alloying followed by consolidation using high-pressure torsion
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
In this research, a new medium-entropy alloy with an equiatomic composition of FeCuNi was designed using a phase diagram (CALPHAD) technique. The FeCuNi MEA was produced from pure iron, copper, and nickel powders through mechanical alloying. The alloy powders were consolidated via a high-pressure torsion process to obtain a rigid bulk specimen. Subsequently, annealing treatment at different conditions was conducted on the four turn HPT-processed specimen. The microstructural analysis indicates that an ultrafine-grained microstructure is achieved after post-HPT annealing, and microstructural evolutions at various stages of processing were consistent with the thermodynamic calculations. The results indicate that the post-HPT-annealed microstructure consists of a dual-phase structure with two FCC phases: one rich in Cu and the other rich in Fe and Ni. The kernel average misorientation value decreases with the increase in the annealing time and temperature, indicating the recovery of HPT-induced dislocations.
Abstract
In this research, a new medium-entropy alloy with an equiatomic composition of FeCuNi was designed using a phase diagram (CALPHAD) technique. The FeCuNi MEA was produced from pure iron, copper, and nickel powders through mechanical alloying. The alloy powders were consolidated via a high-pressure torsion process to obtain a rigid bulk specimen. Subsequently, annealing treatment at different conditions was conducted on the four turn HPT-processed specimen. The microstructural analysis indicates that an ultrafine-grained microstructure is achieved after post-HPT annealing, and microstructural evolutions at various stages of processing were consistent with the thermodynamic calculations. The results indicate that the post-HPT-annealed microstructure consists of a dual-phase structure with two FCC phases: one rich in Cu and the other rich in Fe and Ni. The kernel average misorientation value decreases with the increase in the annealing time and temperature, indicating the recovery of HPT-induced dislocations.
참고문헌 (24)
- Ahad Shafiee, "Development and Microstructural Characterization of a New Wrought High Entropy Superalloy", Metals and Materials International, 26(5), pp.591~602 (2020), 대한금속·재료학회[DOI]
- Anthoula Poulia, "Evaluation of the Microstructural Aspects, Mechanical Properties and Dry Sliding Wear Response of MoTaNbVTi Refractory High Entropy Alloy", Metals and Materials International, 25(6), pp.1529~1540 (2019), 대한금속·재료학회[DOI]
- Xu Chen, "Evolution of Microstructures and Properties in AlxCrFeMn0.8Ni2.1 HEAs", Metals and Materials International, 25(5), pp.1135~1144 (2019), 대한금속·재료학회[DOI]
- P. Asghari-Rad, , Mater. Sci. Eng. A, 744, pp.610~ (2018)
- N. T. C. Nguyen, , Mater. Sci. Eng. A, 764, pp.138198~ (2019)
- P. Asghari-Rad, , Adv. Eng. Mater, 22, pp.1900587~ (2020)
- P. Sathiyamoorthi, , Mater. Sci. Eng. A, 766, pp.138372~ (2019)
- Min Ji Jang, "Plastic Deformation Behavior of 40Fe–25Ni–15Cr–10Co–10V High‑Entropy Alloy for Cryogenic Applications", Metals and Materials International, 25(2), pp.277~284 (2019), 대한금속·재료학회[DOI]
- P. Sathiyamoorthi, , Materialia, 8, pp.100442~ (2019)
- Łukasz Rogal, "Microstructure and Mechanical Properties of Al–Co–Cr–Fe–Ni Base High Entropy Alloys Obtained Using Powder Metallurgy", Metals and Materials International, 25(4), pp.930~945 (2019), 대한금속·재료학회[DOI]
- M. S. El-Eskandarany, (2001), William Andrew Publ
- M. M. Castro, , Adv. Eng. Mater (2019)
- I. V. Alexandrov, , Metall. Mater. Trans. A, 29, pp.2253~ (1998)
- S. Praveen, , Mater. Sci. Eng. A, 735, pp.394~ (2018)
- P. Sathiyamoorthi, , Scr. Mater, 163, pp.152~ (2019)
- S. Praveen, , Mater. Sci. Eng. A, 734, pp.338~ (2018)
- P. Asghari-Rad, , Mater. Sci. Eng. A, 771, pp.138604~ (2020)
- P. Sathiyamoorthi, , Intermetallics, 113, pp.106578~ (2019)
- P. Asghari-Rad, , Adv. Eng. Mater, 19, pp.1600663~ (2017)
- P. Sathiyamoorthi, , Entropy, 20, pp.849~ (2018)
- K. G. Chin, , J. Alloys Compd, 505, pp.217~ (2010)
- 최원미, "Design of New Face-Centered Cubic High Entropy Alloys by Thermodynamic Calculation", Metals and Materials International, 23(5), pp.839~847 (2017), 대한금속·재료학회[DOI]
- T. Raghu, , Mater. Sci. Eng. A, 304-306, pp.438~ (2001)
- S. B. Li, , Mater. Sci. Technol, 20, pp.1345~ (2004)