IN718 초내열 합금의 고속 적층 제조 속도 확보를 위한 최적 VED 활용 공정 변수 제어 방안 연구
Study for the Process Parameter Control to Achieve High Build Rate of Laser Powder Bed Fused IN718 Super Alloy Using Optimal VED
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Recently, considerable attention has been given to nickel-based superalloys used in additive manufacturing. However, additive manufacturing is limited by a slow build rate in obtaining optimal densities. In this study, optimal volumetric energy density (VED) was calculated using optimal process parameters of IN718 provided by additive manufacturing of laser powder-bed fusion. The laser power and scan speed were controlled using the same ratio to maintain the optimal VED and achieve a fast build rate. Cube samples were manufactured using seven process parameters, including an optimal process parameter. Analysis was conducted based on changes in density and melt-pool morphology. At a low laser power and scan speed, the energy applied to the powder bed was proportional to and not . At a high laser power and scan speed, a curved track was formed due to Plateau-Rayleigh instability. However, a wide melt-pool shape and continuous track were formed, which did not significantly affect the density. We were able to verify the validity of the VED formula and succeeded in achieving a 75% higher build rate than that of the optimal parameter, with a slight decrease in density and hardness.
Abstract
Recently, considerable attention has been given to nickel-based superalloys used in additive manufacturing. However, additive manufacturing is limited by a slow build rate in obtaining optimal densities. In this study, optimal volumetric energy density (VED) was calculated using optimal process parameters of IN718 provided by additive manufacturing of laser powder-bed fusion. The laser power and scan speed were controlled using the same ratio to maintain the optimal VED and achieve a fast build rate. Cube samples were manufactured using seven process parameters, including an optimal process parameter. Analysis was conducted based on changes in density and melt-pool morphology. At a low laser power and scan speed, the energy applied to the powder bed was proportional to and not . At a high laser power and scan speed, a curved track was formed due to Plateau-Rayleigh instability. However, a wide melt-pool shape and continuous track were formed, which did not significantly affect the density. We were able to verify the validity of the VED formula and succeeded in achieving a 75% higher build rate than that of the optimal parameter, with a slight decrease in density and hardness.
참고문헌 (22)
- T. DebRoy, , Nat. Mater, 18, pp.1026~ (2019)
- M. Balbaa, , Mat. Des, 193, pp.108818~ (2020)
- 김도혁, "실험계획법을 이용한 Inconel 718의 효율적인 드릴링을 위한 드릴형상 개선에 관한 연구", 한국정밀공학회지, 34(3), pp.161~166 (2017), 한국정밀공학회
- T. Huynh, , Metallogr. Microstruct. Anal, 11, pp.88~ (2022)
- H. Chen, , Acta Mater, 231, pp.117901~ (2022)
- J. S. J. Ten, , J. Laser Appl, 34, pp.012016~ (2022)
- M. C. Sow, , Addit. Manuf, 36, pp.1~ (2020)
- K. G. Prashanth, , Mater. Res. Lett, 5, pp.386~ (2017)
- L. C. Ardila, , Phys. Procedia, 56, pp.99~ (2014)
- M. Tang, , Manuf, 14, pp.39~ (2017)
- U. S. Bertoli, , Mater. Des, 113, pp.331~ (2017)
- P. Ferro, , Int. J. Adv. Manuf. Technol, 110, pp.1911~ (2020)
- N. Nudelis, , Metals, 11, pp.1912~ (2020)
- 이강표, "SLM 기술을 이용한 Ti-6Al-4V 합금의 고속 적층 공정 최적화 연구", 한국결정성장학회지, 28(5), pp.217~221 (2018), 한국결정성장학회[DOI]
- Y. F. Shen, , Key Eng. Mater, 315, pp.357~ (2006)
- I. Yadroitsev, , J. Mater. Process. Technol, 210, pp.1624~ (2010)
- U. Gratzke, , J. Phys. D, 25, pp.1640~ (1992)
- R. Zhang, , J. Phys. D, 53, pp.9~ (2020)
- 우정민, "LPBF 공정으로 제조된 Ti-6Al-4V 합금의 밀도와 표면 거칠기 제어를 위한 매개변수 연구", 한국분말재료학회지, 28(5), pp.410~416 (2021), 한국분말재료학회
- A. Dass, , Coatings, 9, pp.418~ (2019)
- T. N. Le, , Mater. Des, 179, pp.107866~ (2019)
- J. Svensson, , Phys. Rev, 73, pp.205413~ (2006)