CFD를 이용한 컨테이너 선형의 트림별 저항성능 해석
Analysis of Resistance Performance for Various Trim Conditions on Container ship Using CFD
2
조회
0
다운로드
8
인용
0
참고문헌
키워드
초록
Vessels are traditionally optimized for a single condition, normally the contract speed at the design draft. The actual operating conditions quite often differ significantly. At other speed and draft combinations, adjusting the trim can often be used to reduce the hull resistance. Changing the trim is easily done by shifting ballast water. There are several ways to assess the effect of the trim on the hull resistance and fuel consumption, including in-service measurements, model tests, and CFD. In this paper, CFD is employed for the assessment of the resistance performance according to the trim conditions. The commercial CFD code of the STAR-CCM+ is utilized to evaluate the ship's resistance performance on a 6,800 TEU container ship. To validate of the effectiveness of STAR-CCM+, the experimental result of the KCS hull form is compared with the result from STAR-CCM+. It is found that the total resistance of the 6,8000 TEU container ship was reduced by 2.6% in the case of a 1-m trim by head at 18knots.
Abstract
Vessels are traditionally optimized for a single condition, normally the contract speed at the design draft. The actual operating conditions quite often differ significantly. At other speed and draft combinations, adjusting the trim can often be used to reduce the hull resistance. Changing the trim is easily done by shifting ballast water. There are several ways to assess the effect of the trim on the hull resistance and fuel consumption, including in-service measurements, model tests, and CFD. In this paper, CFD is employed for the assessment of the resistance performance according to the trim conditions. The commercial CFD code of the STAR-CCM+ is utilized to evaluate the ship's resistance performance on a 6,800 TEU container ship. To validate of the effectiveness of STAR-CCM+, the experimental result of the KCS hull form is compared with the result from STAR-CCM+. It is found that the total resistance of the 6,8000 TEU container ship was reduced by 2.6% in the case of a 1-m trim by head at 18knots.
참고문헌 (15)
- Buhaug, O., "Second IMO GHG study", 1~40 (2009)
- Cariou, P., "Is Slow Steaming a Sustainable Means of Reducing CO2 Emissions from Container Shipping", Transportation Research Part D : Transport and Environment, 16, pp.260~264 (2011)
- 최정규, "고 레이놀즈수 유동의 수치해석시 벽함수 사용에 관한 연구", 대한조선학회 논문집, 47(5), pp.647~655 (2010), 대한조선학회
- Corbett, J. J., "The Effectiveness and Costs of Speed Reductions on Emissions from International Shipping", Transportation Research Part D : Transport and Environment, 14(6), pp.593~598 (2009)
- Hearn, G. E., "Design for Optimal Hydrodynamic Operation of Large Container Ships", RINA lnternational Coriference on Design and Operation of Container Ships, pp.5~13 (1999)
- Hong, S. -W., "An Experimental Study on Mean Sinkage and Trim Change in Run and Form Factor of Full Hull Form", Journal of the Society of Naval Architects of Korea, 8(1), pp.29~40 (1971)
- 양지만, "대형유조선의 저항추진성능에 미치는 자세변화의 영향에 관한 연구", 대한조선학회 논문집, 43(3), pp.275~284 (2006), 대한조선학회
- Kim, W. -Y., "CFD Analysis on Estimation of Required Power According to Ship's Optimum Trim", 석사, pp.2014
- Lee, J. -K., "Study on the Resistance Performance of Ships with Initial Trim", 석사, pp.2012
- 박동우, "선박의 트림 자세가 저항 성능에 미치는 영향", 대한조선학회 논문집, 50(2), pp.88~94 (2013), 대한조선학회
- 박진모, "해상환경을 고려한 선박항로의 최적화 시나리오 비교분석", 대한조선학회 논문집, 51(2), pp.99~106 (2014), 대한조선학회
- 박상훈, "CFD 저항 해석을 이용한 컨테이너선 최적 트림추정법에 대한 연구", 대한조선학회 논문집, 51(5), pp.429~434 (2014), 대한조선학회
- Sherbaz, S., "Operational Options for Green Ships", Journal of Marine Science and Application, 11(3), pp.335~340 (2012)
- Sherbaz, S., "Ship Trim Optimization : Assessment of Influence of Trim on Resistance of MOERI Container Ship", The Scientific World Journal, 2014, pp.1~6 (2014)
- Van, S., "An Experimental Study on Hull Attitude and Resistance Components of a Ship", Jounal of the Society of Naval Architects of Korea, 24(2), pp.11~19 (1987)