자연대류에서 유한요소법을 이용한 히트싱크의 성능비교
A performance comparison of heat sink using FEM in the natural convection
1
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
The peltier thermoelectric module are used to cool the heat generated by electronic equipment. In order to increase the efficiency of the peltier thermoelectric module, the heat must be released to the outside. A heat sink is used to discharge such heat to the outside. in this paper, two types of heat sinks with internal tunnels were designed. And the heating and cooling performance of the heat sink with internal tunnel structure was compared and analyzed through ANSYS. The heat sink of the A type had better heat transfer than the heat sink of the B type. Which is about 70% improved.
Abstract
The peltier thermoelectric module are used to cool the heat generated by electronic equipment. In order to increase the efficiency of the peltier thermoelectric module, the heat must be released to the outside. A heat sink is used to discharge such heat to the outside. in this paper, two types of heat sinks with internal tunnels were designed. And the heating and cooling performance of the heat sink with internal tunnel structure was compared and analyzed through ANSYS. The heat sink of the A type had better heat transfer than the heat sink of the B type. Which is about 70% improved.
참고문헌 (12)
- Y. Pan, "Performance Analysis and Parametric Optimal Design of an Irreversible Multi-Couple Thermoelectric Refrigerator under various Operating Conditions", Appl. Energy, 84, pp.882~892 (2007)
- M. Chen, "A Three-dimensional Numerical Model of Thermoelectric Generators in Fluid Power Systems", Int. J. Heat Mass Transfer, 54, pp.345~355 (2011)
- Luo, "Optimum Allocation of Heat Transfer Surface Area for Cooling Load and COP Optimization of a Thermoelectric Refrigerator", Energy Convers Manage, 44, pp.3197~3206 (2003)
- D. Champier, "Thermoelectric Power Generation from Biomass Cook Stoves", Energy, 35, pp.935~942 (2010)
- 이동렬, "펠티에 소자 및 히트싱크를 이용한 최적 냉각성능에 관한 연구", 동력시스템공학회지, 10(4), pp.65~70 (2006), 한국동력기계공학회
- S. H. Yu, "Natural Convection Around a Radial Heat Sink", Int. J. Heat Mass Transfer, 53, pp.2935~2938 (2010)
- R. Arularasan, "Modeling and Simulation of A Parallel Plate Heat Sink using Computational Fluid Dynamics", Int. J. Adv. Manuf. Technol, 51, pp.415~419 (2010)
- Bum-Sik Seo, "Development and Characterization of Optimum Heat Sink for 30 W Chip on Board LED Down-Light", Transactions on Electrical and Electronic Materials, 13(6), pp.292~296 (2012), 한국전기전자재료학회[DOI]
- 이민, "자연대류와 강제대류에서 펠티에 소자를 이용한 내부터널 구조를 가지는 히트싱크에 관한 연구", 한국산학기술학회논문지, 15(7), pp.4072~4080 (2014), 한국산학기술학회[DOI]
- P. Teertstra, "A nalytical Forced Convection Modeling Plate Fin H eat Sinks", J. Electronics Manufacturing, 10, pp.253~261 (2000)
- K. T. Chiang, "Applicatio n of Response Surface Methodology in Describing The Thermal Performances of Pin-Fin Heat Sinks", Int. Journal of Thermal Sciences, 48, pp.1196~1205 (2009)
- S. B. Park, "Die Casting Product Desi gn", Press Technology, 11, pp.76~87 (2000)