사출금형코어 및 성형수지 변화에 따른 두께 방향 수축률에 관한 연구
A Study on The Thickness Shrinkage of Injection Molded Parts with The Variation of Injection Mold Core and Molding Materials
1
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
In this study, selective laser sintered 3D printing mold core and metal core were used to investigate the difference of the thickness shrinkage from the gate of the injection molded part at a constant interval. SLS 3D printing mold core was made of nylon-based PA2200 powder and the metal core was manufactured by conventional machining method. As the PA2200 powder material has low strength, thermal conductivity and high specific heat characteristics compared with metal, molding conditions were set with the consideration of molten temperature and injection pressure. Crystalline resin(PP) and amorphous resin(PS) with low melting temperature and viscosity were selected for the injection molding experiment. Cooling time for processing condition was selected by checking the temperature change of the cores with a cavity temperature sensor. The cooling time of the 3D printing core was required a longer time than that of the metal core. The thickness shrinkage of the molded part compared to the core depth was measured from the gate by a constant interval. It was shown that the thickness shrinkage of the 3D printing core was 2.02~4.34% larger than that of metal core. In additions, in the case of metal core, thickness shrinkage was increased with distance from the gate, on the contrary, in the case of polymer core showed reversed aspect.
Abstract
In this study, selective laser sintered 3D printing mold core and metal core were used to investigate the difference of the thickness shrinkage from the gate of the injection molded part at a constant interval. SLS 3D printing mold core was made of nylon-based PA2200 powder and the metal core was manufactured by conventional machining method. As the PA2200 powder material has low strength, thermal conductivity and high specific heat characteristics compared with metal, molding conditions were set with the consideration of molten temperature and injection pressure. Crystalline resin(PP) and amorphous resin(PS) with low melting temperature and viscosity were selected for the injection molding experiment. Cooling time for processing condition was selected by checking the temperature change of the cores with a cavity temperature sensor. The cooling time of the 3D printing core was required a longer time than that of the metal core. The thickness shrinkage of the molded part compared to the core depth was measured from the gate by a constant interval. It was shown that the thickness shrinkage of the 3D printing core was 2.02~4.34% larger than that of metal core. In additions, in the case of metal core, thickness shrinkage was increased with distance from the gate, on the contrary, in the case of polymer core showed reversed aspect.
참고문헌 (10)
- R. Malloy, "Plastic Part Design for Injection Molding" (2010), Hanser Publications
- Precision Prototyping: The Role of 3D Printed Molds in the Injection Molding Industry, "L. L. Zonder", Stratasys Inc, ~ (2013)
- R. A. Harris, "The selection of mould design variables in direct stereolithography injection mould tooling", Journal of Engineering Manufacture IMechE Proceeding part B, 216, pp.499~505 (2002)
- J. G. Kovacs, "Evaluation of measured and calculated thermal parameters of a photopolymer", Int. Commun. Heat Mass Trans, 38, pp.863~867 (2011)
- H. Hassan, "Modeling the effect of cooling system on the shrinkage and temperature of the polymer by injection molding", Applied Thermal Engineering, 30, pp.1547~1557 (2010)
- F. Marin, "Study of the design of cooling channels for polymers injection molds", Polymer Engineering and Science, 58, pp.552~559 (2017)
- H. Hassan, "3D study of cooling system effect on the heat transfer during polymer injection molding", Int. J. Therm, 49, pp.161~169 (2010)
- H. Hassan, "Effect of cooling system on the polymer temperature and solidification during injection molding", Applied Thermal Engineering, 29, pp.1786~1791 (2009)
- Y. Liu, "Evaluation of heat transfer coefficient between polymer and cavity wall for improving cooling and crystallinity results in injection molding simulation", App. Therm, 80, pp.238~246 (2015)
- G. A. Mendible, "Comparative study of rapid and conventional tooling for plastics injection molding", Rapid Prototyping Journal, 23, pp.344~352 (2017)