친환경 소재를 이용한 화장품 쿠션 팩트 용기의 힌지 설계와 사출 성형 시뮬레이션
Hinge Design and Injection Molding Simulation of Cosmetic Cushion Fact Container Using Eco-Friendly Materials
0
조회
0
다운로드
5
인용
0
참고문헌
키워드
초록
As the consumer market in the cosmetic, vehicle manufacturing and aerospace industries grows, the demand for manufacturing industries using on injection mold technology. Also, such manufacturing technology of metal machining is expensive, and the shape is limited. Cosmetic cushion fact products are divided into outer relevant to the exterior of the product and inner containers containing the actual contents. In the case of the inner container, it needs to be combined with the upper and lower cases. As environmental regulations are strengthened internationally, the use of a large number of component parts can result in significant losses in recycling and economics. Therefore, this study aims to perform injection molding analysis through injection molding simulation to develop a cushion fact container that can be recycled through the unification of products and materials using polypropylene to cope with environmental regulations. In the case of injection molding conditions, Injection Time(sec): 4.5, Cooling Time(sec): 13, Resin Temperature(℃): 240, and Pressure(MPa): 30 were determined. The results of injection molding simulation according to the two design methods were compared with the sync mark which shows the problem of filling and injection molding.
Abstract
As the consumer market in the cosmetic, vehicle manufacturing and aerospace industries grows, the demand for manufacturing industries using on injection mold technology. Also, such manufacturing technology of metal machining is expensive, and the shape is limited. Cosmetic cushion fact products are divided into outer relevant to the exterior of the product and inner containers containing the actual contents. In the case of the inner container, it needs to be combined with the upper and lower cases. As environmental regulations are strengthened internationally, the use of a large number of component parts can result in significant losses in recycling and economics. Therefore, this study aims to perform injection molding analysis through injection molding simulation to develop a cushion fact container that can be recycled through the unification of products and materials using polypropylene to cope with environmental regulations. In the case of injection molding conditions, Injection Time(sec): 4.5, Cooling Time(sec): 13, Resin Temperature(℃): 240, and Pressure(MPa): 30 were determined. The results of injection molding simulation according to the two design methods were compared with the sync mark which shows the problem of filling and injection molding.
참고문헌 (10)
- 박은민, "금형대류열전달계수가 사출성형 수치모사에 미치는 영향 고찰", 대한기계학회논문집 B, 43(3), pp.201~209 (2019), 대한기계학회
- 정진우, "플라스틱-금속 복합 성형을 위한 내부삽입형 가열구조 연구", 대한기계학회논문집 A, 43(2), pp.145~152 (2019), 대한기계학회
- 안동규, "3개의 캐비티를 가지는 냉장고 내상의 3차원 진공 열성형 해석", 대한기계학회논문집 A, 40(5), pp.505~511 (2016), 대한기계학회
- 신성현, "사출금형코어 및 성형수지 변화에 따른 두께 방향 수축률에 관한 연구", Design & Manufacturing, 13(2), pp.17~21 (2019), 한국금형공학회[DOI]
- 정성택, "친환경 고생산성을 위한 단일 쿠션 팩트 내 화장품 용기의 사출 시뮬레이션 분석", Design & Manufacturing, 12(2), pp.51~56 (2018), 한국금형공학회[DOI]
- 안동규, "3 차원 사출성형 해석을 통한 컴퓨터 마우스 제작용 이중사출성형 금형의 공정조건 결정", 대한기계학회논문집 A, 35(12), pp.1619~1625 (2011), 대한기계학회
- 안동규, "부분적으로 후육부를 가지는 평판형 제품의 제작을 위한 사출성형 금형의 냉각채널 설계에 관한 연구", 한국정밀공학회지, 29(8), pp.824~833 (2012), 한국정밀공학회[DOI]
- Hakimian, E., "Analysis of warpage and shrinkage properties of injection-molded micro gears polymer composites using numerical simulations assisted by the Taguchi method", Materials & Design, 42, pp.62~71 (2012)
- Liu, Y., "Evaluation of heat transfer coefficient between polymer and cavity wall for improving cooling and crystallinity results in injection molding simulation", Applied Thermal Engineering, 80, pp.238~246 (2015)
- Zink, B., "The effect of limescale on heat transfer in injection molding", International Communications in Heat and Mass Transfer, 86, pp.101~107 (2017)