MCD 및 NCD 코팅 볼 엔드밀의 정삭가공에서의 최적절삭조건에 관한 연구
A study on optimal cutting conditions of MCD or NCD coated ball end-mills for finishing
3
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Recently, several studies are being conducted to achieve a curvature of 180° or more for the edge of the display glass. The thermocompression molding process is applied to the manufacture of curved glass, and high hardness G5 graphite is used as the mold material to withstand the impact applied to the mold. G5 graphite has high hardness and strong brittleness, which makes tool wear and surface damage easy during machining. Therefore, the demand for diamond-coated tools with good mechanical properties is increasing in the G5 machining field. In this study, the optimal cutting conditions and machinability of a nanodiamond (NCD) coated ball end mill being developed by a tool manufacturer were analyzed and evaluated. For this purpose, the same test was performed on the microdiamond (MCD) coated ball end mill and compared together. In summary, the machinability of MCD and NCD coated tools showed better cutting performance at a cutting speed of 282 m/min, a feed rate of 1,400 mm/min, and a radial depth of cut of 0.08 to 0.1 mm.
Abstract
Recently, several studies are being conducted to achieve a curvature of 180° or more for the edge of the display glass. The thermocompression molding process is applied to the manufacture of curved glass, and high hardness G5 graphite is used as the mold material to withstand the impact applied to the mold. G5 graphite has high hardness and strong brittleness, which makes tool wear and surface damage easy during machining. Therefore, the demand for diamond-coated tools with good mechanical properties is increasing in the G5 machining field. In this study, the optimal cutting conditions and machinability of a nanodiamond (NCD) coated ball end mill being developed by a tool manufacturer were analyzed and evaluated. For this purpose, the same test was performed on the microdiamond (MCD) coated ball end mill and compared together. In summary, the machinability of MCD and NCD coated tools showed better cutting performance at a cutting speed of 282 m/min, a feed rate of 1,400 mm/min, and a radial depth of cut of 0.08 to 0.1 mm.
참고문헌 (14)
- Ashby, M. F., "Materials Selection in Mechanical Design" (2005), Elsevier Butterworth–Heinemann
- Yang, Y. K., "Optimization of dry machining parameters for high-purity graphite in endmilling pro-cess via design of experiments methods", J. Mater. Process. Technol, 209, pp.4395~4400 (2009)
- Singla, A., "Micro and nano-crystalline diamond coatings of co-cemented tungsten carbide tools with their characterization", J. Bio-Tribo-Corros, 7, pp.1~11 (2021)
- Bian, R., "Experimental investigation on ductile mode micro-milling of ZrO2 ceramics with diamond-coated end mills", Micromachines, 9, pp.127~ (2018)
- Hodroj, A., "Nanocrystalline diamond coatings : Effects of time modulation bias enhanced HFCVD parameters", AIMS Materials Science, 5(3), pp.519~532 (2018)
- Wang, H., "Cutting performances of MCD, SMCD, NCD and MCD", NCD coated tools in high-speed milling of hot bending graphite molds, 2020, pp.276, 116401~
- Lee, H., "Analysis of Tool Wear and Roughness of Graphite Surfaces Machined Using MCD and NCD-Coated Ball Endmills", Micromachines, 13, pp.766~ (2022)
- 홍광표, "커버 글래스 엣지 가공을 위한 다이아몬드 입자 전착 공구 제작 및 가공성 평가", Design & Manufacturing, 11(1), pp.1~6 (2017), 한국금형공학회
- 하석재, "마이크로 금형 부품을 위한 마이크로 절삭가공 기술", Design & Manufacturing, 13(1), pp.5~12 (2019), 한국금형공학회[DOI]
- 정성택, "단결정 다이아몬드공구 제작 기술을 통한 초정밀 미세패턴 가공 연구", Design & Manufacturing, 14(3), pp.63~70 (2020), 한국금형공학회[DOI]
- 서금희, "EPS 엔드밀 가공 시 표면 거칠기에 미치는 가공조건에 관한 연구", Design & Manufacturing, 11(2), pp.46~50 (2017), 한국금형공학회
- 정성택, "밀링 공구의 역 공학 설계에서 3D 유한요소 해석을 통한 절삭력 실험의 신뢰성 검증", Design & Manufacturing, 13(2), pp.54~59 (2019), 한국금형공학회[DOI]
- Yang, M. Y., "Machining –Theory and Reality", pp.41~43 (2001), Cheongmoon
- Ko, T. J., "Selection of Machining Inclination Angle of Tool Considering Tool Wear in High Speed Ball End Milling", J. Korean Society of Precision Engineering, 15(9), pp.135~144 (1998)