스텐실 개구홀 크기 변화에 따른 솔더프린팅 인쇄효율 평가
Evaluation of Solder Printing Efficiency with the Variation of Stencil Aperture Size
1
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
표면실장형 수동소자인 0402, 0603, 1005 칩에 대한 인쇄 주요인자 결정 및 공정 최적화를 실험계획법을 통해 실시하였다. 실험에 사용된 솔더는 Sn-3.0Ag-0.5Cu와 Sn-0.7Cu이며, 공정변수로는 스텐실 두께, 스퀴지 각도, 인쇄 속도, 기판분리 속도, 스텐실과 기판간의 갭이며, 인쇄압력은 2 kgf/cm²로 고정하였다. 분산분석을 통해 인쇄효율에 영향을미치는 주요인자가 스텐실 두께와 스퀴지 각도임을 확인할 수 있었다. 주요인자인 스텐실 두께와 스퀴지 각도를 변화시켜인쇄효율의 최적화 영역을 확인하였고, 0402, 0603, 1005 칩 모두 스퀴지 각도가 45˚ 이하일 경우 인쇄효율이 높았다. 스텐실 두께를 변화할 경우 칩 크기에 따라 인쇄효율이 다른 양상을 보였는데, 0402, 0603 칩에서는 스텐실 두께가 얇을수록 높은 인쇄효율을 보였으며, 1005 칩에서는 스텐실 두께가 두꺼울수록 높은 인쇄효율을 나타내었다.
Abstract
Main parameters of the screen printing were determined and the printing parameters were optimized for 0402,0603, and 1005 chips in this study. The solder pastes used in this study were Sn-3.0Ag-0.5Cu and Sn-0.7Cu. The process parameters were stencil thickness, squeegee angle, printing speed, stencil separating speed and gap between stencil and PCB. The printing pressure was fixed at 2 kgf/cm². From ANOVA results, the stencil thickness and the squeegee angle were determined to be main parameters for the printing efficiency. The printing efficiency was optimized with varying two main parameters, the stencil thickness and the squeegee angle. The printing efficiency increased as the squeegee angle was lowered under 45˚ for all chips. For the 0402 and the 0603 chips, the printing efficiency increased as the stencil thickness decreased. On the other hand, for the 1005 chip, the printing efficiency increased as the stencil thickness increased.
참고문헌 (14)
- R. S. Clouthier, "The Complete Solder Paste Printing Processes", Surf. Mount Technol, 13(1), pp.6~ (1999)
- D. C. Montgomery, "Using Statistically Designed Experiments for Process Development and Improvement: An Application in Electronics Manufacturing", Robotics and Computer Integrated Manufacturing, (16), pp.55~ (2000)
- D. He, "Monte Carlo Study of Solder Paste Microstructure and Ultrafine-pitch Stencil Printing", J. Mater. Sci, (14), pp.501~ (2003)
- A. Lofti, "Industrial Application of Fuzzy Systems: Adaptive Fuzzy Control of Solder Paste Stencil Printing", Information Sciences, (107), pp.273~ (1998)
- T. Wilson, "An Optimistic Outlook for Ultra Fine Pitch(part I)", Electron. Prod., Feb, (39) (1995)
- J. A. Owczarek, "A Study of the Off-contact Screen Printing Process(part I): Model of the Printing Process and Some Results Derived from Experiment", IEEE Trans. Compo., Hybrids, Manuf. Technol, 13(2), pp.358~ (1990)
- J. Pan, "Critical Variables of Solder Paste Stencil Printing for Micro-BGA and Fine-Pitch QFP", IEEE Trans. Electon. Packag. Manufact, 27(2), pp.125~ (2004)
- T. A. Nguty, "The Rheological Properties of Solder and Solar Pastes and the Effect on Stencil Printing", Rheologica Acta, (39), pp.607~ (2000)
- 서원상, "솔더 페이스트를 이용한 스크린 프린팅 공정 해석", 마이크로전자 및 패키징학회지, 17(1), pp.47~53 (2010), 한국마이크로전자및패키징학회
- 배성민, "생산기반기술 디지털화를 위한 지식공유형 플랫폼 개발: 전자패키지 표면실장기술을 중심으로", 마이크로전자 및 패키징학회지, 18(1), pp.1~5 (2011), 한국마이크로전자및패키징학회
- 권치명, "시뮬레이션 실험에서 중심합성계획의 응용", Journal of The Korean Data Analysis Society, 7(1), pp.333~345 (2005), 한국자료분석학회
- S. H. Mannan, "Squeegee Deformation Study in the Stencil Printing of Solder Pastes", IEEE Trans. Compo., Package., Manuf. Technol, (17), pp.70~ (1994)
- M. Whitmore, "New Developments in Broadband Printing Techniques", Proc. SMTA International Conference (2010), Surface Mount Technology Association (SMTA)
- O. Krammer, "Modelling the Effect of Uneven PWB Surface on Stencil Bending during Stencil Printing Process", Microelectron, 52(1) (2011), Reliab