Electroless Nickel Autocatalytic Gold (ENAG) 표면처리와 Sn-Ag-Cu솔더 간 접합부의 계면반응 및 취성파괴 신뢰성 비교 연구
Comparative Study of Interfacial Reaction and Drop Reliability of the Sn-3.0Ag-0.5Cu Solder Joints on Electroless Nickel Autocatalytic Gold (ENAG)
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
본 연구에서는 Sn-Ag-Cu (SAC)솔더와 electroless nickel autocatalytic gold (ENAG) 표면처리 간 계면반응 및낙하충격 신뢰성을 연구하였다. ENAG 솔더 접합부의 특성은 다른 Ni계 표면처리인 electroless nickel immersion gold (ENIG)와 electroless nickel electroless palladium immersion gold (ENEPIG)와 비교 평가 하였다. SAC솔더와 Ni계 표면처리 계면에서는 (Cu, Ni)6Sn5 intermetallic compound (IMC)가 형성되었다. IMC 두께는 SAC/ENAG와 SAC/ENEPIG 는 1.15 ㎛, 1.12 ㎛로 비슷하였고, SAC/ENIG는 IMC 두께가 2.99 ㎛로 SAC/ENAG보다 2배 정도 높았다. 또한 솔더접합부의 IMC두께는 무전해 Ni(P) 도금액의 metal turnover (MTO)조건에 영향을 받는 다는 것을 알 수 있었고, MTO가0에서 3으로 증가하면 IMC두께가 증가함을 알 수 있었다. 전단강도는 SAC/ENEPIG의 접합강도가 가장 높았고, SAC/ ENAG, SAC/ENIG 순이었다. 또한, MTO가 증가하면, 전단강도가 낮아짐을 알 수 있었다. 취성파괴도 SAC/ENEPIG가세가지 접합부 중 가장 낮았으며, SAC/ENAG, SAC/ENIG 순이였고, 마찬가지로 MTO가 증가하면 취성파괴가 높아짐을알 수 있었다. 낙하충격 시험에서도 0 MTO조건이 3 MTO조건보다 높은 평균파괴횟수를 갖는 것을 확인하였고, 평균파괴횟수도 SAC/ENEPIG, SAC/ENAG, SAC/ENIG순으로 높았다. 낙하 충격 후 파단면을 관찰한 결과 크랙은 IMC와 Ni(P) 층 사이에서 진행되었다.
Abstract
In this study, the interfacial reaction and drop impact reliability of Sn-Ag-Cu (SAC) solder and electroless nickel autocatalytic gold (ENAG) were studied. In addition, the solder joint properties with the ENAG surface finish was compared with electroless nickel immersion gold (ENIG) and electroless nickel electroless palladium immersion gold (ENEPIG). The IMC thickness of SAC/ENAG and SAC/ENEPIG were 1.15 and 1.12 ㎛, respectively, which were similar each other. The IMC thickness of the SAC/ENIG was 2.99 ㎛, which was about two times higher than that of SAC/ ENAG. Moreover, it was found that the IMC thickness of the solder joint was affected by the metal turnover (MTO) condition of the electroless Ni(P) plating solution, and it was found that the IMC thickness increased when the MTO increased from 0 to 3. The shear strength of SAC/ENEPIG was the highest, followed by SAC/ENAG and SAC/ENIG. It was found that when the MTO increased, the shear strength was lowered. In terms of brittle fracture, SAC/ENEPIG was the lowest among the three joints, followed by SAC/ENAG and SAC/ENIG. Likewise, it was found that as MTO increased, brittle fracture increased. In the drop impact test, it was confirmed that the 0 MTO condition had a higher average number of failures than the 3 MTO condition, and the average number of failures was also higher in the order of SAC/ENEIG, SAC/ENAG, and SAC/ENIG. As a result of observing the fracture surface after the drop impact, it was found that the fracture was between the IMC and the Ni(P) layer.
참고문헌 (29)
- A. Siewiorek, "Effects of PCB Substrate Surface Finish and Flux on Solderability of Lead-Free SAC305 Alloy", J. Mater. Eng. Perform, 22(8), pp.2247~ (2013)
- M. Ratzker, "Review of Capabilities of the ENEPIG Surface Finish", J. Electron. Mater, 43(11), pp.3885~ (2014)
- K. H. Kim, "Effect of Plasma Surface Finish on Wettability and Mechanical Properties of SAC305 Solder Joints", J. Electron. Mater, 45(12), pp.6184~ (2016)
- X. Luhua, "Intermetallic Growth Studies on SAC", ENIG and SAC, Thermal and Thermomechanical Proceedings 10th Intersociety Conference on Phenomena in Electronics Systems (ITH-ERM), pp.2006[DOI]
- W. Seo, "Effect of NiP Plating Temperature on Growth of Interfacial Intermetallic Compound in Electroless Nickel Immersion Gold", Sn-Ag-Cu Solder Joints, 2018, pp.47(1), 110~
- W. Seo, "Effect of Bath Life of Ni(P) on the Brittle-Fracture Behavior of Sn-3.0Ag-0.5Cu", ENIG, 2014, pp.43(12), 4457~
- P. Snugovsky, "Electroless Ni", Immersion Au Interconnects: Investigation of Black Pad in Wire Bonds and Solder Joints, 2001, pp.30(9), 1262~
- K. H. Kim, "A Corrosion Couple Experiment Reproducing the Black Pad Phenomenon Found after the Electroless Nickel Immersion Gold Process", Scr. Mater, 63(5), pp.508~ (2010)
- K. Zeng, "Root Cause of Black Pad Failure of Solder Joints with Electroless Nickel", Immersion Gold Plating, 2006, ~[DOI]
- 백종훈, "0.1 ㎛ Ni두께를 가지는 얇은 ENEPIG 층과 Sn-3.0Ag-0.5Cu 솔더와의 계면반응 및 접합강도", 대한용접접합학회지, 35(6), pp.51~58 (2017), 대한용접접합학회[DOI]
- P. Chi, "Effect of Ni(P) Layer Thickness on Interface Reaction and Reliability of Ultrathin Enepig Surface Finish", Materials, 14(24), pp.7874~ (2021)
- C. Shen, "Packaging Reliability Effect of ENIG and ENEPIG Surface Finishes in Board Level Thermal Test under Long-Term Aging and Cycling", Materials, 10(5), pp.451~ (2017)
- B. K. Kim, "Origin of Surface Defects in PCB Final Finishes by the Electroless Nickel Immersion Gold Process", J. Electron. Mater, 37(4), pp.527~ (2008)
- F. Song, "High-Speed Solder Ball Shear and Pull Tests vs . Board Level Mechanical Drop Tests : Correlation of Failure Mode and Loading Speed", 2007 Proceedings 57th Electronic Components and Technology Conference (2007), IEEE
- "JESD22-B117A:solder ball shear", JEDEC Solid State Technology Association, ~ (2003)
- "JESD22-B111:board level drop test method of component for handheld electronics products", JEDEC Solid State Technology Association, ~ (2003)
- 서원일, "무전해 니켈 도금액 pH 변화에 따른 ENIG", Sn-Ag-Cu솔더 접합부의 취성파괴 특성, 2020, pp.27(3), 29~34[DOI]
- H. Lee, "Characterization of the Contamination Factor of Electroless Ni Plating Solutions on the ENIG Process", J. Electron. Mater, 47(9), pp.5158~ (2018)
- P. E. Tegehall, "Review of the Impact of Intermetallic Layers on the Risk for Brittle Fractures in Solder Joints", Proceedings of the IMAPS Nordic Annual Conference (2006)
- K. Newman, "BGA Brittle Fracture-Alternative Solder Joint Integrity Test Methods", Proceedings Electronic Components and Technology, ECTC'05 (2005), IEEE
- 김경호, "ENEPIG", Sn-Ag-Cu 솔더 접합부의 취성 파괴에 미치는 무전해 니켈 도금액의 영향, 2017, pp.35(3), 1~6[DOI]
- H. Matsuki, "TEM Observation of Interfaces in a Solder Joint in a Semiconductor Device", Sci. Technol. Adv. Mater, 3(3), pp.261~ (2002)
- T. Laurila, "Interfacial Reactions between Lead-Free Solders and Common Base Materials", Mater. Sci. Eng.: R: Reports, 49(1), pp.1~ (2005)
- I. Shohji, "Tensile Properties of Sn-Ag Based Lead-Free Solders and Strain Rate Sensitivity", Mater. Sci. Eng.: A, 366(1), pp.50~ (2004)
- G. Xiao, "Strain Rate Sensitivity of Sn-3.0Ag-0.5Cu Solder Investigated by Nanoindentation", Mater. Sci. Eng.: A, 613, pp.336~ (2014)
- S. Liu, "The Effects of Precipitation Strengthening and Solid Solution Strengthening on Strain Rate Sensitivity of Lead-Free Solders", Microelectron. Reliab, 84, pp.170~ (2018)
- Wonil Seo, "Growth of intermetallic compounds and brittle fracture behavior of Sn-Ag-Cu", ENIG joint with columnar Ni-P layer, 2020, pp.32(1), 1042~1051[DOI]
- Y. C. Lin, "Suppressing Ni–Sn–P growth in SnAgCu", Ni–P solder joints, 2007, pp.56(1), 49~
- 하상옥, "OSP•ENIG 표면 처리된 기판과 Sn-3.0Ag-0.5Cu 솔더 접합부의 낙하충격 신뢰성 평가", 마이크로전자 및 패키징학회지, 16(1), pp.33~38 (2009), 한국마이크로전자및패키징학회