마모 입자가 음향방출신호에 미치는 영향에 관한 연구
Investigation of the Effect of Wear Particles on the Acoustic Emission Signal
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
In spite of progress in tribological research, machine component failure due to friction and wear has been reported frequently. This failure may lead to secondary damage that can cause huge expense for maintenance and repair. To prevent economic loss, it is important to detect and predict the initial failure point. In this sense, various researchers have been tried to develop Condition Monitoring (CM) method using Acoustic Emission (AE) generated while the materials undergo failure. In this study, effect of particles on friction and wear was investigated using the pin-on-plate friction test and AE signal was recorded with a band-width type AE sensor. The experiments were performed in dry and lubricant conditions using steel and glass as specimens. After the experiment, 3D laser microscope image was captured to evaluate the wear behavior quantitatively. The AE signal was analyzed in time-domain and frequency-domain. The amplitude was compared with the frictional results. The results of this study showed that particle generation accelerate wear, generate high magnitude AE signal and change the frequency characteristics of the signal. Also, lubricant condition test results showed low coefficient of friction, low wear rate, and low magnitude of AE signal compared to the dry condition. It is expected that the results of this study will aid in better assessment of wear in CM technology.
Abstract
In spite of progress in tribological research, machine component failure due to friction and wear has been reported frequently. This failure may lead to secondary damage that can cause huge expense for maintenance and repair. To prevent economic loss, it is important to detect and predict the initial failure point. In this sense, various researchers have been tried to develop Condition Monitoring (CM) method using Acoustic Emission (AE) generated while the materials undergo failure. In this study, effect of particles on friction and wear was investigated using the pin-on-plate friction test and AE signal was recorded with a band-width type AE sensor. The experiments were performed in dry and lubricant conditions using steel and glass as specimens. After the experiment, 3D laser microscope image was captured to evaluate the wear behavior quantitatively. The AE signal was analyzed in time-domain and frequency-domain. The amplitude was compared with the frictional results. The results of this study showed that particle generation accelerate wear, generate high magnitude AE signal and change the frequency characteristics of the signal. Also, lubricant condition test results showed low coefficient of friction, low wear rate, and low magnitude of AE signal compared to the dry condition. It is expected that the results of this study will aid in better assessment of wear in CM technology.
참고문헌 (15)
- 이태훈, "ZI 및 ZA형 웜기어의 치합전달오차 해석", 한국트라이볼로지학회지, 34(6), pp.325~331 (2018), 한국트라이볼로지학회[DOI]
- 전상명, "모터링 시동 및 시동정지 사이클에서 경사진 축을 갖는 저어널베어링의 마모 해석 – Part I: 마모발생 가능영역에서의 유막 변화 연구", 한국트라이볼로지학회지, 33(4), pp.153~167 (2017), 한국트라이볼로지학회[DOI]
- 강경모, "고탄소크롬 베어링강 2종(SUJ2) 베어링강에 증착된 저마찰 코팅의 트라이볼로지적 특성 연구", 한국트라이볼로지학회지, 34(6), pp.254~261 (2018), 한국트라이볼로지학회[DOI]
- 한도렬, "인산을 이용한 법랑 코팅의 초윤활성 및초기 시간에 대한 연구", 한국트라이볼로지학회지, 34(6), pp.235~240 (2018), 한국트라이볼로지학회[DOI]
- Hase M., "The Relationship between Acoustic Emissions and Wear Particles for repeated Dry Rubbing", Wear, 265(5-6), pp.831~839 (2008)
- Tchakoua P., "Wind Tur-bine Condition Monitoring: State-of-the-art Review, New Trends, and Future Challenges", Energies, 7(4), pp.2595~2630 (2014)
- 김동현, "음향방출 에너지 파라미터를 이용한 고로 철피균열의 조기 결함탐지 기술", 비파괴검사학회지, 36(1), pp.45~52 (2016), 한국비파괴검사학회[DOI]
- Gao Guodong, "Monitoring the Evolution of Crazing Damage in an Area under Stress Concentration via Acoustic Emission", International Journal of Precision Engineering and Manufacturing, 19(4), pp.561~568 (2018), 한국정밀공학회
- Lee S. M., "Relationship between Takeoff Behavior of Hard-disk Slider and AE Signal", J. Korean Soc. Tribol. Lubr. Eng., 17(1), pp.40~55 (2001)[DOI]
- Hase M., "Correlation between Features of Acoustic Emission Signals and Mechan-ical Wear Mechanisms", Wear, 292, pp.144~150 (2012)
- 남재현, "Effect of Groove Surface on Friction Noise and Its Mechanism", International Journal of Precision Engineering and Manufacturing, 18(8), pp.1165~1172 (2017), 한국정밀공학회
- Chung K. H., "Particle Monitoring Method Using Acoustic Emis-sion Signal for Analysis of slider", disk, Tribol. Int., pp.2004, 37(10)[DOI]
- Chang H., "Acous-tic Emission Study of Fatigue Crack closure Closure of Physical Short and Long Cracks for Aluminum Alloy LY12CZ", Int. J. Fatigue, 31(3), pp.403~407 (2009)
- Sagasta F., "Lamb Modes Detection Using Cumulative Shannon Entropy with Improved Estimation of Arrival Time", J. Nondestr. Eval, 38(1) (2019)
- 김혜균, "기판 종류에 따른 물 윤활 특성 및 나노 입자의 영향", 한국트라이볼로지학회지, 33(6), pp.245~250 (2017), 한국트라이볼로지학회[DOI]