엔진 파이어링동안 일정 축 각속도에서 비고정식 피스톤-핀과 연결봉-소단부 부싱 및 피스톤-핀 보스의 접촉면 마모해석
Wear Analysis at the Interface of Connecting-Rod Small-End Bushing and Piston-Pin Boss with a Floating Piston-Pinat Constant Angular Velocity during Engine Firing
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
In recently designed diesel engines, the running conditions for piston-pin bearings have become severe because of the higher combustion pressure and increased temperature. Moreover, the metal removal from the bushing material has strongly reduced the ability of the antifriction material to accept asperity contacts. Therefore, it is necessary to find ways of reducing wear scar on the connecting-rod small-end bushing and piston-pin boss bearing related to the higher combustion pressure on the power cell of an engine. In this work, the position and level of material removal from the surfaces of the bushing and bearing under such severe operating conditions - for example, maximum power and torque conditions of a passenger car diesel engine - are estimated for several combinations of surface roughness. First, piston-pin rotating motion is investigated by calculating the friction coefficient at piston-pin bearings, the oil film thickness, and the frictional torques induced by hydrodynamic shear stress. Subsequently, the wear scarring on the surfaces of a connecting-rod small-end bushing and two piston-pin boss bearings related to piston-pin rotational motion is numerically calculated under the maximum power and torque operating conditions. This work is helpful to determine the reasonable surface roughness of the bushing and bearing for reducing wear volume occurring at the interface between a bearing and a shaft.
Abstract
In recently designed diesel engines, the running conditions for piston-pin bearings have become severe because of the higher combustion pressure and increased temperature. Moreover, the metal removal from the bushing material has strongly reduced the ability of the antifriction material to accept asperity contacts. Therefore, it is necessary to find ways of reducing wear scar on the connecting-rod small-end bushing and piston-pin boss bearing related to the higher combustion pressure on the power cell of an engine. In this work, the position and level of material removal from the surfaces of the bushing and bearing under such severe operating conditions - for example, maximum power and torque conditions of a passenger car diesel engine - are estimated for several combinations of surface roughness. First, piston-pin rotating motion is investigated by calculating the friction coefficient at piston-pin bearings, the oil film thickness, and the frictional torques induced by hydrodynamic shear stress. Subsequently, the wear scarring on the surfaces of a connecting-rod small-end bushing and two piston-pin boss bearings related to piston-pin rotational motion is numerically calculated under the maximum power and torque operating conditions. This work is helpful to determine the reasonable surface roughness of the bushing and bearing for reducing wear volume occurring at the interface between a bearing and a shaft.
참고문헌 (32)
- Tomita, K., "A Study of Rotating Motion of Piston Pin in Gasoline Engine", JSAE Proceedings, pp.25~28 (1994)
- Piston Pin: Wear and Rotating Motion, "Ligier, J. L.", SAE International, 760~768, pp.SAE 2005-01-1651 (SP-1964) (2005)
- Chun, S. M., "Study on the Rotating Motion of a Piston Pin of Full Floating Type", J. of the KSTLE, 23(3), pp.95~102 (2007)
- 전상명, "고 연소압을 받는 디젤엔진 피스톤의 핀-보스 베어링 윤활해석", 한국트라이볼로지학회지, 24(3), pp.133~139 (2008), 한국트라이볼로지학회
- Sang Myung Chun, "Wear simulation for the journal bearings operating under aligned shaft and steady load during start-up and coast-down conditions", Tribology International, 97, pp.440~466 (2016), Elsevier BV[DOI]
- 전상명, "모터링 시동 및 시동정지 사이클에서 경사진 축을 갖는 저어널베어링의 마모 해석 – Part I: 마모발생 가능영역에서의 유막 변화 연구", 한국트라이볼로지학회지, 33(4), pp.153~167 (2017), 한국트라이볼로지학회[DOI]
- 전상명, "모터링 시동 및 시동정지 사이클에서 경사진 축을 갖는 저어널베어링의 마모 해석 - Part II: 경사진 축을 지지하는 두 저어널베어링의 마모해석", 한국트라이볼로지학회지, 33(4), pp.168~186 (2017), 한국트라이볼로지학회[DOI]
- 전상명, "파이어링 상태의 일정 축 각속도에서 엔진 베어링의 마모 해석 – Part I: 베어링 마모발생 부위 파악", 한국트라이볼로지학회지, 34(3), pp.93~106 (2018), 한국트라이볼로지학회[DOI]
- 전상명, "파이어링 상태의 일정 축 각속도에서 엔진베어링의 마모 해석− Part II: 저어널베어링 마모 계산", 한국트라이볼로지학회지, 34(4), pp.146~159 (2018), 한국트라이볼로지학회[DOI]
- 전상명, "파이어링 시동 사이클 초기에서의 엔진 베어링 마모 시뮬레이션", 한국트라이볼로지학회지, 35(4), pp.244~266 (2019), 한국트라이볼로지학회[DOI]
- Chun, S. M., "Parametric Study of Thermal and Unsteady Effects in Hydrodynamic Lubrication of Journal Bearings", Ph. D., pp.1989
- Booker, J. F., "Dynamically Loaded Journal Bearings : Mobility Method of Solution", Trans. Of the ASME, J. of Basic Engineering, 87, pp.537~546 (1965)
- Booker, J. F., "Dynamically-Loaded Journal Bearings : Numerical Application of the Mobility Method", Trans. of the ASME, J. of Lubrication Technology, 93(1), pp.168~176 (1971)
- Goenka, P. K., "Analytical Curve Fits for Solution Parameters of Dynamically Loaded Journal Bearings", J of Reibology, Trans. ASME, 106, pp.421~428 (1984)
- X. Lu, "On the Lift-off Speed in Journal Bearings", Tribology Letters, 20(3-4), pp.299~305 (2005), Springer Science and Business Media LLC[DOI]
- Chun, S. M., "Parametric Study of Inlet Oil Temperature and Pressure for a Half-Circumferential Grooved Journal Bearing", Tribol. Trans, 35(2), pp.213~224 (1992)
- Sang Myung Chun, "Aeration effects on the performance of a turbocharger journal bearing", Tribology International, 41(4), pp.296~306 (2008), Elsevier BV[DOI]
- Ligterink, D. J., "Measurements of Wear in Radial Journal Bearings", Tribotest Journal, 3(1), pp.45~54 (1996)
- Zhao, Y., "An Asperity Microcontact Model Incoporating the Transition from Elastic Deformation to Fully Plastic Flow", Trans. ASME, J. Tribol, 122, pp.86~93 (2000)
- Masjedi, M., "Film Thickness and Asperity Load Formulas for Line-Contact Elastohydrodynamic Lubrication with Provision for Surface Roughness", Trans. ASME, J. Tribol, 134(1) (2012)[DOI]
- McCool, J. I., "Relating Profile Instrument Measurements to the Functional Performance of Rough Surfaces", Trans. ASME, J. Tribol, 109(2), pp.264~270 (1987)
- Kingsbury, E. P., "Some Aspect of the thermal desorption of a boundary lubricant", J. Appl. Phys, 29, pp.888~891 (1958)
- Rowe, C. N., "Some aspects of heat of adsorption in function of a boundary lubricant", ASLE Trans, 9, pp.101~111 (1966)
- Holm, R., "Electrical contacts" (1946), Almqvist & Wiksell
- Archard, J. F., "Contact and rubbing of flat surfaces", J. Appl. Phys, 24, pp.981~988 (1953)
- Ali Beheshti, "Asperity micro-contact models as applied to the deformation of rough line contact", Tribology International, 52, pp.61~74 (2012), Elsevier BV[DOI]
- Kogut, L., "Elastic-Plastic Contact Analysis of a Sphere and a Rigid Flat", Trans. ASME, J. Applied Mechanics, 69, pp.657~662 (2002)
- Kogut, L., "A Finite Element based Elastic-Plastic Model for the Contact of Rough Surfaces", Tribol. Trans, 46, pp.383~390 (2003)
- Viscosity of Motor Oil, "LIN, H. L.", Fedral Mogul, Engineering, ~ (1981)
- Hamrock, B. J., "Fundamentals of Fluid Film Lubrication", pp.57~63 (1994)
- Patir, N., "An average Flow Model for Determining Effects of Three-Dimensional Roughness on Partial Hydrodynamic Lubrication", ASME J. Lubr. Technol, 100, pp.12~17 (1978)
- Queener, C. A., "Transient wear of machine parts", Wear, 25, pp.391~400 (1965)