Urea-SCR시스템 액막형 선회분사기의 분사압력변화에 따른 무특성에 관한 연구
Effect of injection pressure on the atomization characteristics of a liquid sheet-type swirl injector for Urea-SCR system
0
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
Urea-SCR시스템에 적용하기 위한 액막형 선회분사기의 분사압력변화에 따른 분무특성이 실험적으로 조사되었다. 실험에 사용된 노즐은 형상비 3.1을 갖는 단공 압력식 액막형 선회노즐이며, 노즐선단에분사되는 유체에 선회류를 형성하기 위한 선회기가 설치되어 있다. 노즐의 분사량 조절은 PWM(pulse width modulation)기법에 의해 제어되었다. 분무의 발달과정은 2차원 PIV에 의해 가시화되었으며, 분무각변화가 조사되었다. 분무액적의 속도 및 크기는 2차원 PDPA에 의해 상온 대기압 조건에서 측정되었다. 분무구조는 분사압력에 큰 영향을 받으며, SMD는 분사압력 증가에 따라 감소하며 선행연구자의 반실험적 결과와 유사한 경향을 보임을 알 수 있었다.
Abstract
In this study, the spray characteristics of a pressure swirl atomizer classified into a liquid sheet-type swirl nozzle for Urea-SCR system were investigated experimentally with the variation of injection pressure. The length to diameter ratio (lo/d) of the nozzle was 3.1, and the swirler was set inside the nozzle tip to give injecting fluid angular momentum. The injection duration of the nozzle was controlled by PWM (pulse width modulation) modes. The development processes of the spray were imaged by a 2-D PIV system, and the change of spray angle was measured. The atomization characteristics, including axial velocity and SMD,were measured using a 2-D PDA system with the injection pressures at room temperature and ambient pressure conditions. As the experimental results, the injection pressure had a significant impact on the spray structure showing a different shape around the spray leading edge, and the smaller SMD was observed with increasing injection pressures, which was similar to that of the previous work.
참고문헌 (22)
- Diesel emission control in review, "T. V. Johnson", Society of Automotive Engineers, ~, pp.2007-01-0233 (2007)
- The influence of ammonia to NOx ratio on SCR performance, "J. Girard", Society of Automotive Engineers, ~, pp.Technical Paper 2007-01-1581 (2007)
- Modeling of copper-zeolite and iron-zeolite selective catalytic reduction (SCR) catalysts at steady state and transient conditions, "K. Narayanaswamy", Society of Automotive Engineers, ~, pp.Technical Paper 2008-01-0615 (2008)
- Case studies of urea SCR integration on passenger cars monitoring of urea inside the tank during hot and cold environment test missions, "J. Thompson", Society of Automotive Engineers, ~, pp.Technical Paper 2008-01-1181 (2008)
- Optimization of catalytic converter gas flow distribution by CFD prediction, "H. Weltens", Society of Automotive Engineers, ~, pp.Technical paper 930780 (1993)
- Investigation on uniformity indices used for diesel exhaust aftertreatment systems, "Å. Johansson", Society of Automotive Engineers, ~, pp.Technical Paper 2008-01-0613 (2008)
- A study of a new aftertreatment system(1): A new dosing device for enhancing low temperature performance of Urea-SCR, "T. Kowatari", Society of Automotive Engineers, ~, pp.Technical Paper, 2006-01-0642 (2006)
- A study of a new aftertreatment system(2): control of urea solution spray for Urea-SCR, "A. Nishioka", Society of Automotive Engineers, ~, pp.Technical Paper, 2006-01-0644 (2006)
- Simulation on the optimum shape and location of urea injector for Urea-SCR system of heavy-duty diesel engine to prevent NH3 slip, "S. J. Jeong", Society of Automotive Engineers, ~, pp.Technical Paper, 2005-01-3886 (2005)
- Z. Huang, "Formation and reaction of ammonium sulfate salts on V2O5", AC catalyst during selective catalytic reduction of nitric oxide by ammonia at low temperatures, 2003, pp.214, 213~219
- S. M. Kang, "Effect of assist air flowrate on the atomization characteristics in a dual air supplying twin-fluid swirl nozzle", Proceedings of Fall Conference of The Korean Society of Mechanical Engineers, pp.11~16 (2007)
- D. W. Yang, "Breakup characteristics of liquid sheet type swirl injector using LIF technique", Proceedings of Fall Conference of The Korean Society of Mechanical Engineers, pp.2930~2936 (2010)
- 함윤영, "Urea-SCR 시스템의 공기보조형 분사노즐 형상에 따른 DeNOx 특성 연구", 한국자동차공학회 논문집, 17(6), pp.67~73 (2009), 한국자동차공학회
- 김기두, "중형 디젤엔진의 연료분사노즐 형상에 따른 성능해석연구", 한국마린엔지니어링학회지, 30(6), pp.662~668 (2006), 한국마린엔지니어링학회
- B. J. Rho, "Swirl effect on the spray characteristics of a twin-fluid jet", The Korean Society of Mechanical Engineers International Journal, 12(5), pp.899~906 (1998)
- S. Y. Lee, "Atomization of the Liquid", pp.166~167 (1996), Minumsa Co
- Y. Nakayama, "Action of the fluid in the air micrometer : first report, characteristics of small diameter nozzle and orifice", Bull. Japan Society of Mechanical Engineers, 4, pp.516~524 (1961)
- S. M. Jeng, "Computational and experimental study of liquid sheet emanating from simplex fuel nozzle", The American Institute of Aeronautics and Astronautics Journal, 36(2) (1998)
- An analysis of ambient air entrainment into split injection D.I. gasoline spary by LIF-PIV technique, "J. K. Lee", Society of Automotive Engineers, ~, pp.Technical Paper, 2002-01-2662 (2002)
- J. K. Lee, "Breakup process of initial spray of D.I. gasoline injector by LIF imaging technique", 13th International Symposium on Applications of Laser Techniques to Fluid Mechanics (2006)
- H. Lefebvre, "Atomization and Sprays", pp.215~217 (1989), Hemisphere Publishing Corporation
- S. Y. Lee, "Atomization of the Liquid", pp.194~196 (1996), Minumsa Co.