GaAs MMIC상에서 주기적으로 천공된 홀을 가지는 접지 금속막 구조를 이용한 전송선로 특성연구 및 코프레너 선로를 이용한 온칩 초소형 임피던스 변환기에의 응용
A Study on Characteristics of the Transmission Line Employing Periodically Perforated Ground Metal on GaAs MMIC and Its Application to Highly Miniaturized On-chip Impedance Transformer Employing Coplanar Waveguide
2
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
In this paper, basic characteristics of transmission line employing PPGM (periodically perforated ground metal) were investigated using theoretical and experimental analysis.According to the results, unlike the conventional PBG (photonic band gap) structures, the characteristic impedance of the transmission line employing PPGM structure showed a real value, which exhibited a very small dependency on frequency. The transmission line employing PPGM structure showed a loss (per quarter wave length) higher by 0.1 ∼0.2 dB than the conventional microstrip line. According to the investigation of the dependency of RF characteristic on ground condition, the RF characteristic of the transmission line employing PPGM structure was hardly affected by the ground condition in the frequency lower than Ku band, but fairly affected in the frequency higher than Ku band, which indicated that coplanar waveguide employing PPGM structure was optimal for RF characteristic and reduction of size. Considering above results, impedance transformer was developed using coplanar waveguide with PPGM structure for the first time, and good RF characteristics were observed from the impedance transformer. In case that λ/4 impedance transformer with a center frequency of 9 GHz was fabricated for a impedance transformation from 20 to10 Ω, the line width and length were 20 and 500 μm, respectively, and its size was only 0.64 % of the impedance transformer fabricated with conventional microstrip lines. Above results indicate that the transmission line employing PPGM is a promising candidate for a development of matching and passive elements on MMIC.
Abstract
In this paper, basic characteristics of transmission line employing PPGM (periodically perforated ground metal) were investigated using theoretical and experimental analysis.According to the results, unlike the conventional PBG (photonic band gap) structures, the characteristic impedance of the transmission line employing PPGM structure showed a real value, which exhibited a very small dependency on frequency. The transmission line employing PPGM structure showed a loss (per quarter wave length) higher by 0.1 ∼0.2 dB than the conventional microstrip line. According to the investigation of the dependency of RF characteristic on ground condition, the RF characteristic of the transmission line employing PPGM structure was hardly affected by the ground condition in the frequency lower than Ku band, but fairly affected in the frequency higher than Ku band, which indicated that coplanar waveguide employing PPGM structure was optimal for RF characteristic and reduction of size. Considering above results, impedance transformer was developed using coplanar waveguide with PPGM structure for the first time, and good RF characteristics were observed from the impedance transformer. In case that λ/4 impedance transformer with a center frequency of 9 GHz was fabricated for a impedance transformation from 20 to10 Ω, the line width and length were 20 and 500 μm, respectively, and its size was only 0.64 % of the impedance transformer fabricated with conventional microstrip lines. Above results indicate that the transmission line employing PPGM is a promising candidate for a development of matching and passive elements on MMIC.
참고문헌 (12)
- H. Wang, "Silicon-based monolithic millimeter-wave integrated circuits", Asia-Pacific Microwave Conf., pp.268~275 (2006)
- S. K. Alam, "A 1.5-V 2.4 GHz CMOS variable gain front-end for bluetoothand wireless LAN applications", Asia-Pacific Microwave Conf., pp.1139~1142 (2006)
- H. Yukawa, "12-GHz low noise MIC amplifier with 0.86 dB noise figure", Asia-Pacific Microwave Conf., pp.181~184 (2006)
- S. Kurachi, "A wideband amplifier MMIC with InGaP", GaAs HBT technology, 2005, 764~766
- Y. Yun, "A Novel Microstrip-Line Structure Employing a Periodically Perforated Ground Metal and Its Application to Highly Miniaturized and Low-Impedance Passive Components Fabricated on GaAs MMIC", IEEE Trans Microwave Theory Tech, 53, pp.1951~1959 (2005)
- D. Ahn, "A design of low-pass filter using the novel microstrip defected ground structure", IEEE Trans. Microwave Theory Tech, 49, pp.86~93 (2001)
- F. R. Yang, "A UC-PBG structure and its applications for microwave circuits", IEEE Trans. Microwave Theory Tech, 47(8), pp.1509~1514 (1999)
- J. Gao, "Per-Unit-Length Parameters of 1-D CPW Metamaterials with Simultaneously Series-C and Shunt-L Loading", Asia-Pacific Microwave Conf., pp.39~42 (2005)
- C. S. Kim, "A novel 1-D periodic defected ground structure for planar circuits", IEEE Microwave Guided Wave Lett, 10(4), pp.131~133 (2001)
- A. S. Andrenko, "Application of PBG microstrip circuits for enhancing the performance of high-density substrate patch antennas", Microwave Opt.Tech.Lett, 32(5), pp.340~344 (2002)
- A. Lai, "Microwave composite right", left-handed metamaterials and devices, 2005, 31~34
- D. M. Pozar, "Microwave Engineering" (1990), Addison-Wesley