피스톤 링 실 끝단을 갖는 스퀴즈 필름 댐퍼의 감쇠 계수 측정
Measurement of Damping Coefficients of a Squeeze Film Damper with Piston Ring Seal Ends
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
This study experimentally identifies the effects of end shape, clearance, total damper length, journal eccentricity ratio, oil supply pressure, and oil flow rate on the damping coefficient of a squeeze film damper (SFD) with piston ring seal ends and a central groove. The SFD is composed of a lubricating fluid flowing between the outer race of a rolling element bearing and cartridge, along with an anti-rotation pin to prevent the rotation of the outer race. The device provides additional viscous damping to a rotating system. Additionally, piston ring seals attached at both ends of the damper increase the damping coefficient of the rotating system by reducing oil leakage. Because these different design conditions affect the damping coefficient of an SFD, we perform experiments including different conditions. Tests show that the damping coefficient increases significantly in the SFD with piston ring seal ends compared with the SFD with open ends. The damping coefficient also increases with increasing total damper length and journal eccentricity ratio, and decreases with increasing clearance. Additionally, in contrast to the trend observed for the SFD with open ends, the damping coefficient for the SFD with piston ring seal ends increases with increasing supply pressure and flow rate as the frequency decreases but shows consistent results as the frequency increases.
Abstract
This study experimentally identifies the effects of end shape, clearance, total damper length, journal eccentricity ratio, oil supply pressure, and oil flow rate on the damping coefficient of a squeeze film damper (SFD) with piston ring seal ends and a central groove. The SFD is composed of a lubricating fluid flowing between the outer race of a rolling element bearing and cartridge, along with an anti-rotation pin to prevent the rotation of the outer race. The device provides additional viscous damping to a rotating system. Additionally, piston ring seals attached at both ends of the damper increase the damping coefficient of the rotating system by reducing oil leakage. Because these different design conditions affect the damping coefficient of an SFD, we perform experiments including different conditions. Tests show that the damping coefficient increases significantly in the SFD with piston ring seal ends compared with the SFD with open ends. The damping coefficient also increases with increasing total damper length and journal eccentricity ratio, and decreases with increasing clearance. Additionally, in contrast to the trend observed for the SFD with open ends, the damping coefficient for the SFD with piston ring seal ends increases with increasing supply pressure and flow rate as the frequency decreases but shows consistent results as the frequency increases.
참고문헌 (10)
- San Andrés, L., "Identification of Force Coefficients in a Squeeze Film Damper with a Mechanical End Seal-Part I : Unidirectional Load Tests", J. Eng Gas Turbines power, 129(3), pp.858~864 (2007)[DOI]
- San Andrés, L., "Identification of Force Coefficients in a Squeeze Film Damper with a Mechanical End Seal-Centered Circular Orbit Tests", J. Tribol, 129(3), pp.660~668 (2007)[DOI]
- San Andrés, L., "Damping and Inertia Coefficients for Two End Sealed Squeeze Film Dampers with a Central Groove : Measurements and Predictions", J. Eng Gas Turbines power, 135(11), pp.112503~ (2013)[DOI]
- Jeung, S. H., "Effect of Oil Supply Pressure on the Force Coefficients of a Squeeze Film Damper Sealed with Piston Rings", J. Tribol, 141(6), pp.061701~ (2019)[DOI]
- San Andrés, L., "Experimental Force Coefficients for Two Sealed Ends Squeeze Film Dampers (Piston Rings and O-Rings): An Assessment of their Similarities and Differences", J. Eng Gas Turbines power, 141(2), pp.021024~ (2019)[DOI]
- Levesley, M. C., "The effect of oil supply and sealing arrangements on the performance of squeeze-film dampers : an experimental study", Proc. IME. J. J. Eng. Tribol, 210(4), pp.221~232 (1996)
- Fan, T., "Investigation into the effect of piston ring seals on an integrated squeeze film damper model", J. Mech. Sci. Tech, 33(2), pp.559~569 (2019)
- San Andrés, L., "Model and Experimental Verification of the Dynamic Forced Performance of a Tightly Sealed Squeeze Film Damper Supplied with a Bubby Mixture", J. Eng. Gas Turbines Power, 142(1), pp.011023~ (2020)[DOI]
- San Andrés, L., "Squeeze film dampers: an experimental appraisal of their dynamic performance", First Asia Turbomachinery and Pump Symposium (2016)
- Kim, N. K., "Experimental Identification of the Damping Characteristics of a Squeeze Film Damper with Open Ends and Central Groove", Tribol. Lubr, 40(1), pp.28~37 (2024)[DOI]