수종 Automixing 레진시멘트의 물성과 상아질에 대한 전단결합강도
Physical Properties of Different Automixing Resin Cements and the Shear Bond Strength on Dentin
0
조회
0
다운로드
2
인용
0
참고문헌
키워드
초록
본 연구에서는 여러 automixing 레진시멘트의 물성과 상아질에 대한 전단결합강도를 평가, 비교하고자 하였다. Self-adhesive automixing 레진시멘트인 Rely-X Unicem(3M ESPE, St. Paul, USA), Embrace resin cement(Pulpdent, Oakland, USA)와 chemical polymerizing automixing 레진시멘트인 Resiment Ready-Mix(J.L.Blosser Inc., Liberty Missouri, USA)를 사용하였다. 물성을 평가하기 위하여 레진시멘트를 테프론 주형에 주입한 후 자가중합을 시키고 24시간 동안 빛이 차단된 상태로 100% 상대습도에 보관 후 만능 시험기를 이용하여 압축강도, 간접인장강도, 굴곡강도를 측정하였다. 상아질에 대한 전단결합강도를 평가하기 위하여 발거한 하악 제3대구치의 협측 상아질을 노출 시킨 후 일정한 크기로 레진시멘트를 부착시킨 뒤 만능 시험기를 이용하여 전단결합강도를 측정하였다. SPSS Ver 12.0(SPSS Inc., Chicago, IL, USA)을 사용하여 95% 유의수준에서 One way ANOVA test로 분석하였으며 Scheffe test로 사후검정 하였다. 연구결과, chemical polymerizing automixing 레진시멘트가 self-adhesive automixing 레진시멘트에 비해 상대적으로 높은 물리적 성질과 상아질에 대한 전단결합강도를 보였다.
Abstract
The purpose of this study was to evaluate the physical properties of different automixing resin cements and the shear bond strength on dentin. For this study, two self-adhesive automixing resin cement(Rely-X Unicem(3M ESPE, St. Paul, USA), Embrace resin cement(Pulpdent, Oakland, USA)) and one chemical polymerizing resin cement(Resiment Ready-Mix(J.L.Blosser Inc., Liberty Missouri, USA)) were used. To evaluate the physical properties, compressive strength, diametral tensile strength and flexural strength were measured. The specimens were fabricated using Teflon mould according to manufacturers' instructions and stored for 24 hours in an atmosphere of 100% humidity. To evaluate the shear bond strength on dentin, each cements were adhered to buccal dentinal surface of extracted human lower molars in 2mm diameter. Physical properties and shear bond strengths were measured using universal testing machine(Z010, Zwick GmbH, Ulm, Germany) at a crosshead speed of 0.5mm/min. The physical properties and shear bond strength of different automixing resin cements were statistically analyzed and compared between groups using One-way ANOVA test and Schffe post-hoc test at the 95% level of confidence. The result shows that chemical polymerizing automixing resin cement represents the relatively higher physical properties and shear bond strength than self-adhesive automixing resin cements.
참고문헌 (24)
- Theodore M, "Dental Materials", pp.217~219 (2001), Mosby
- Zhen Chun Li, "Mechanical properties of dental luting cements", J Prosthot Dent, 81, pp.597~609 (1999)
- De Munck J, "Bonding of an auto-adhesive luting material to enamel and dentin", Dent Mater, 20, pp.963~971 (2004)
- Mak YF, "Micro-tensile bond testing of resin cements to dentin and an indirect resin composite", Dent Mater, 18, pp.609~621 (2002)
- Fusayama T, "Non-pressure adhesion of a new adhesive restorative resin", J Dent Res, 58(4), pp.1364~1370 (1979)
- Nicholls JI, "The effect of convergence angle variation on the computed stresses in the luting agent", J Prosthet Dent, 31, pp.651~657 (1974)
- Nicholls JI, "Stress analysis of symmetric restorations", J Prosthet Dent, 31, pp.179~184 (1974)
- Yettram AL, "Finite element stress analysis of the crowns of normal and restored teeth", J Dent Res, 55, pp.1004~1011 (1976)
- Craig RG, "Stress analysis and design of single restorations and fixed bridges", Oral Sci Rev, 10, pp.45~74 (1977)
- Farah JW, "Stress analysis of three marginal configurations of full posterior crowns by three- dimensional photoelasticity", J Dent Res, 53, pp.1219~1225 (1974)
- Chai JY, "Effects of labial margin design on stress distribution of a porcelain-fused-to-metal crown", J Prosthodont, 1, pp.18~23 (1992)
- Goldstein GR, "Flexion characteristics of four-unit fixed partial denture frameworks using holographic interferometry", J Prosthet Dent, 67, pp.609~613 (1992)
- Kamposiora P, "Finite element analysis estimates of cement microfracture under complete veneer crowns", J Prosthet Dent, 71, pp.435~441 (1994)
- O'Brien WJ, "Dental materials: properties and selection", pp.167~171 (1997), Quintessence
- Harry F, "Tooth-colored restoratives", pp.93~97 (2002), BC Decker Inc
- Derkson GD, "Clinical evaluation of posterior composite restorations : Two year results", J Dent Res, 49(4), pp.277~279 (1983)
- Chae MS, "A study on the compressive strength of experimental light-actived composite resins", J Kor Res Soc Dent Mat, 22(2), pp.113~121 (1995)
- Kawaguchi M, "Mechanical properties and curing depth of urethane tetramethacrylate-based composite resins", Shika Zairyo Kikai, 9(5), pp.762~766 (1990)
- Soeno K, "Influence of mechanical properties of two resin cements on durability of bond strength to dentin after cyclic loading", Dent Mater J, 24(3), pp.351~355 (2005)
- Salz U, "Self-curing, self-etching adhesive cement systems", J Adhes Dent, 7(1), pp.7~17 (2005)
- Abo-Hamar SE, "Bond strength of a new universal self-adhesive resin luting cement to dentin and enamel", Clin Oral Investig, 9(3), pp.161~167 (2005)
- Bateman GJ, "Retention of quartz-fibre endodontic posts with a self-adhesive dual cure resin cement", Eur J Prosthodont Restor Dent, 13(1), pp.33~37 (2005)
- Mallmann A, "Microtensile bond strength of light- and self-cured adhesive systems to intraradicular dentin using a translucent fiber post", Oper Dent, 30(4), pp.500~506 (2005)
- Seltzer S, "The penetration of micro-organism between the tooth and direct resin fillings", J Am Dent Assoc, 51, pp.560~566 (1955)