측정장치의 compliance 유무가 복합레진의 중합수축응력의 측정에 미치는 영향
EFFECT OF INSTRUMENT COMPLIANCE ON THE POLYMERIZATION SHRINKAGE STRESS MEASUREMENTS OF DENTAL RESIN COMPOSITES
1
조회
0
다운로드
5
인용
0
참고문헌
키워드
초록
본 연구에서는 측정장치의 compliance 유무가 복합레진의 중합수축응력 측정에 미치는 영향을 알아보았다. 변위센서, cantilever load cell과 부궤환 (negative feedback) 시스템을 적용하여 compliance를 허용하는 것과 허용하지 않는 두 가지 모드로 중합수축응력의 측정이 가능한 stress-strain analyzer를 제작하였다. 한 종의 flowable (Filtek Flow: FF) 복합레진과 두 종의 universal hybrid (Z100: Z1 and Z250: Z2) 복합레진이 사용되었다. Load cell의 끝과 base plate에 고정된 직경 3.0 mm 의 금속 막대에 silane을 처리하였다. 1.0 mm의 거리로 고정한 두 개의 금속 막대 사이에 복합레진을 적용한 후 광중합을 하였다. 복합레진의 수직 중합수축률과 중합수축응력을 10 분 동안 기록하였고 인장탄성계수도 구하였다. 통계처리는 일원분산분석과 paired t-test를 시행하였고 95% 유의수준에서 Tukey's test로 사후 검정하였다. 측정된 중합수축 응력은 재료와 compliance의 유무에 따라 큰 차이를 보였다. Compliance를 허용한 모드에서 중합 수축응력은 FF: 3.11 (0.13)이 가장 컸으며 Z1: 2.91 (0.10), Z2: 1.94 (0.09) MPa의 순서였다. 측정장치의 compliance를 허용하지 않은 경우에는 Z1: 17.08 (0.89)이 가장 컸고 FF: 10.11 (0.29), Z2: 9.46 (1.63) MPa의 순이었다. 또한 Z1, Z2, FF의 인장탄성계수는 각각 2.31 (0.18), 2.05 (0.20), 1.41 (0.11) GPa 이었다. 중합수축응력은 compliance mode에서는 복합레진의 수직 중합수축률이 주요 영향 요인이었으며, compliance를 배제한 모드에서는 탄성계수의 효과가 지배적이었다.
Abstract
The purpose of this study was to evaluate the effect of instrument compliance on the polymerization shrinkage stress measurements of dental composites. The contraction strain and stress of composites during light curing were measured by a custom made stress-strain analyzer, which consisted of a displacement sensor, a cantilever load cell and a negative feedback mechanism. The instrument can measure the polymerization stress by two modes: with compliance mode in which the instrument compliance is allowed, or without compliance mode in which the instrument compliance is not allowed. A flowable (Filtek Flow: FF) and two universal hybrid (Z100: Z1 and Z250: Z2) composites were studied. A silane treated metal rod with a diameter of 3.0 mm was fixed at free end of the load cell, and other metal rod was fixed on the base plate. Composite of 1.0 mm thickness was placed between the two rods and light cured. The axial shrinkage strain and stress of the composite were recorded for 10 minutes during polymerization, and the tensile modulus of the materials was also determined with the instrument. The statistical analysis was conducted by ANOVA, paired t-test and Tukey's test (α<0.05). There were significant differences between the two measurement modes and among materials. With compliance mode, the contraction stress of FF was the highest: 3.11 (0.13), followed by Z1: 2.91 (0.10) and Z2: 1.94 (0.09) MPa. When the instrument compliance is not allowed, the contraction stress of Z1 was the highest: 17.08 (0.89), followed by FF: 10.11 (0.29) and Z2: 9.46 (1.63) MPa. The tensile modulus for Z1,Z2 and FF was 2.31 (0.18), 2.05 (0.20), 1.41 (0.11) GPa, respectively. With compliance mode, the measured stress correlated with the axial shrinkage strain of composite; while without compliance the elastic modulus of materials played a significant role in the stress measurement
참고문헌 (33)
- Braga RR, "Alternatives in polymerization contraction stress management", Crit Rev Oral Biol Med, 15(3), pp.176~184 (2004)
- Kleverlaan CJ, "Polymerization shrinkage and contraction stress of dental resin composites", Dent Mater, 21(12), pp.1150~1157 (2005)
- Song YX, "Linear shrinkage of photo-activated composite resins during setting", J Oral Rehabil, 28(4), pp.335~341 (2001)
- Lee IB, "A new method to measure the polymerization shrinkage kinetics of light cured composites", J Oral Rehabil, 32(4), pp.304~314 (2005)
- Dauvillier BS, "Developments in shrinkage control of adhesive restoratives", J Esthet Dent, 12(6), pp.291~299 (2000)
- Carvalho RM, "A review of polymerization contraction: the influence of stress development versus stress relief", Oper Dent, 21(1), pp.17~24 (1996)
- Park J, "How should composite be layered to reduce shrinkage stress: incremental or bulk filling?", Dent Mater, 24(11), pp.1501~1505 (2008)
- Lee MR, "Influence of cavity dimension and restoration methods on the cusp deflection of premolars in composite restoration", Dent Mater, 23(3), pp.288~295 (2007)
- Labella R, "Polymerization shrinkage and elasticity of flowable composites and filled adhesives", Dent Mater, 15(2), pp.128~137 (1999)
- Guggenberger R, "Exploring beyond methacrylates", Am J Dent, 13, pp.82~84 (2000)
- Chantler PM, "An extension of a phenomenological model for dental composites", Dent Mater, 15(2), pp.144~149 (1999)
- Venhoven BA, "Light initiation of dental resins: dynamics of the polymerization", Biomaterials, 17(24), pp.2313~2318 (1996)
- Feilzer AJ, "Setting stress in composite resin in relation to configuration of the restoration", J Dent Res, 66(11), pp.1636~1639 (1987)
- Park J, "How should composite be layered to reduce shrinkage stress: incremental or bulk filling?", Dent Mater, 24(11), pp.1501~1505 (2008)
- Lutz E, "Elimination of polymerization stresses at the margins of posterior composite resin restorations: a new restorative technique", Quintessence Int, 17(12), pp.777~784 (1986)
- Bowen RL, "Adhesive bonding of various materials to hard tooth tissues: forces developing in composite materials during hardening", J Am Dent Assoc, 106(4), pp.475~477 (1983)
- Bowen RL, "Adhesive bonding of various materials to hard tooth tissues. VI. Forces developing in direct-filling materials during hardening", J Am Dent Assoc, 74(3), pp.439~445 (1967)
- Hegdahl T, "Contraction stresses of composite resin filling materials", Acta Odontol Scand, 35(4), pp.191~195 (1977)
- Bouschlicher MR, "Effect of composite type, light intensity, configuration factor and laser polymerization on polymerization contraction forces", Am J Dent, 10(2), pp.88~96 (1997)
- Watts DC, "Photo-polymerization shrinkage-stress kinetics in resin-composites: methods development", Dent Mater, 19(1), pp.1~11 (2003)
- Chen HY, "Polymerization contraction stress in light-cured compomer restorative materials", Dent Mater, 19(7), pp.597~602 (2003)
- Chen HY, "Polymerization contraction stress in light-cured packable composite resins", Dent Mater, 17(3), pp.253~259 (2001)
- Lu H, "Probing the origins and control of shrinkage stress in dental resin-composites: I. Shrinkage stress characterization technique", J Mater Sci Mater Med, 15(10), pp.1097~1103 (2004)
- Braga RR, "Contraction stress of flowable composite materials and their efficacy as stress-relieving layers", J Am Dent Assoc 134, 134(6), pp.721~728 (2003)
- Braga RR, "Contraction stress related to degree of conversion and reaction kinetics", J Dent Res, 81(2), pp.114~118 (2002)
- Condon JR, "Assessing the effect of composite formulation on polymerization stress", J Am Dent Assoc, 131(4), pp.497~503 (2000)
- Braga RR, "Alternatives in polymerization contraction stress management", Crit Rev Oral Biol Med, 15(3), pp.176~184 (2004)
- Lee SH, "Influence of instrument compliance and specimen thickness on the polymerization shrinkage stress measurement of lightcured composites", Dent Mater, 23(9), pp.1097~1100 (2007)
- Watts DC, "Shrinkage stress reduction in resin-composites of increasing particle concentration (abstract 2444)", J Dent Res, 81, pp.a~308 (2002)
- Feilzer AJ, "Effect of TEGDMA", BisGMA ratio on stress development and viscoelastic properties of experimental two-paste composites, 2003, pp.82(10), 824~828
- 라성호, "광조사 강도가 복합레진의 중합반응속도에 미치는 영향에 관한 실시간 체적측정법을 이용한 연구", 대한치과보존학회지, 27(2), pp.135~141 (2002), 대한치과보존학회
- 박준규, "5급 와동의 복합레진 수복 시 발생되는 교두굴곡에 관한 연구", 대한치과보존학회지, 33(2), pp.83~89 (2008), 대한치과보존학회
- 이인복, "수직 진동형 Rheometer를 이용한 복합레진의 유변학적 성질의 측정", 대한치과보존학회지, 29(6), pp.489~497 (2004), 대한치과보존학회