Evaluation of corrosion resistance of Co-Cr alloys fabricated with different metal laser sintering systems
1
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
PURPOSE. The aim of this study was to evaluate the corrosion resistance of the specimens produced by five different commercial metal laser sintering (MLS) systems with their recommended Co-Cr alloy powders. MATERIALS AND METHODS. The MLS machines and the alloy powders used were, ProX 100-ST2724G (St-Pro), Mysint 100-EOS SP2 (SP2-Mys), EOSINT 270-EOS SP2 (SP2-EOS), SLM 100-Starbond CoS (SB-SLM), and MLab Cusing-Remanium® Star (RS-MLab), respectively. Eight specimens from each group were prepared. Open circuit potential (Eocp) and electrochemical impedance spectroscopy (EIS) measurements of polished surfaces of the specimens were conducted in a three-electrode cell using a potentiostat-galvanostat in Fusayama-Meyer artificial saliva (AS). Specimens from each group were immersed in AS and de-ionized water for seven days. Eocp, charge transfer resistance (Rct) values, and released ions (μg/cm2 × 7d) in different solutions were determined. The specimen surfaces were observed with SEM/EDS. Results were analyzed statistically. RESULTS. Eocp values have shifted to potentials that are more positive over time. Steady-state Eocp values were from high to low as follows, SB-SLM, SP2-Mys, SP2-EOS, RS-MLab, and ST-Pro, respectively. After 60 mins, RS-MLab specimens had the highest Rct value, followed by SP2-Mys, SB-SLM, SP2-EOS, and ST-Pro. In all groups, ion release was higher in AS than that in de-ionized water. CONCLUSION. There were small differences among the corrosion resistances of the Co-Cr alloy specimens produced with MLS systems; meanwhile, the corrosion resistances were quite high for all specimens.
Abstract
PURPOSE. The aim of this study was to evaluate the corrosion resistance of the specimens produced by five different commercial metal laser sintering (MLS) systems with their recommended Co-Cr alloy powders. MATERIALS AND METHODS. The MLS machines and the alloy powders used were, ProX 100-ST2724G (St-Pro), Mysint 100-EOS SP2 (SP2-Mys), EOSINT 270-EOS SP2 (SP2-EOS), SLM 100-Starbond CoS (SB-SLM), and MLab Cusing-Remanium® Star (RS-MLab), respectively. Eight specimens from each group were prepared. Open circuit potential (Eocp) and electrochemical impedance spectroscopy (EIS) measurements of polished surfaces of the specimens were conducted in a three-electrode cell using a potentiostat-galvanostat in Fusayama-Meyer artificial saliva (AS). Specimens from each group were immersed in AS and de-ionized water for seven days. Eocp, charge transfer resistance (Rct) values, and released ions (μg/cm2 × 7d) in different solutions were determined. The specimen surfaces were observed with SEM/EDS. Results were analyzed statistically. RESULTS. Eocp values have shifted to potentials that are more positive over time. Steady-state Eocp values were from high to low as follows, SB-SLM, SP2-Mys, SP2-EOS, RS-MLab, and ST-Pro, respectively. After 60 mins, RS-MLab specimens had the highest Rct value, followed by SP2-Mys, SB-SLM, SP2-EOS, and ST-Pro. In all groups, ion release was higher in AS than that in de-ionized water. CONCLUSION. There were small differences among the corrosion resistances of the Co-Cr alloy specimens produced with MLS systems; meanwhile, the corrosion resistances were quite high for all specimens.
참고문헌 (43)
- Tuna SH, "Corrosion resistance assessment of Co-Cr alloy frameworks fabricated by CAD", CAM milling, laser sintering, and casting methods, 2015, pp.114, 725~734
- Lu Y, "Investigation on the microstructure, mechanical property and corrosion behavior of the selective laser melted CoCrW alloy for dental application", Mater Sci Eng C Mater Biol Appl, 49, pp.517~525 (2015)
- Davis JR, "ASM specialty handbook: Nickel, cobalt, and their alloys", pp.343~401 (2000), ASM International
- Simchi A, "Direct laser sintering of metal powders: Mechanism, kinetics and microstructural features", Mater Sci Eng A Struct Mater, 428, pp.148~158 (2006)
- Mumtaz KA, "High density selective laser melting of Waspaloy®", J Mater Process Technol, 195, pp.77~87 (2008)
- Zhou Y, "Comparative analysis of the microstructures and mechanical properties of Co-Cr dental alloys fabricated by different methods", J Prosthet Dent, 120, pp.617~623 (2018)
- Han X, "Comparative analysis of mechanical properties and metal-ceramic bond strength of Co-Cr dental alloy fabricated by different manufacturing processes", Materials(Basel), 11, pp.1801~ (2018)
- Ucar Y, "Internal fit evaluation of crowns prepared using a new dental crown fabrication technique : laser-sintered Co-Cr crowns", J Prosthet Dent, 102, pp.253~259 (2009)
- Takaichi A, "Microstructures and mechanical properties of Co-29Cr-6Mo alloy fabricated by selective laser melting process for dental applications", J Mech Behav Biomed Mater, 21, pp.67~76 (2013)
- Wang H, "Evaluation of metal-ceramic bond characteristics of three dental Co-Cr alloys prepared with different fabrication techniques", J Prosthet Dent, 116, pp.916~923 (2016)
- Qian B, "Defects-tolerant Co-Cr-Mo dental alloys prepared by selective laser melting", Dent Mater, 31, pp.1435~1444 (2015)
- Wataha JC, "Alloys for prosthodontic restorations", J Prosthet Dent, 87, pp.351~363 (2002)
- Hedberg YS, "In vitro biocompatibility of CoCrMo dental alloys fabricated by selective laser melting", Dent Mater, 30, pp.525~534 (2014)
- Hong MH, "The influence of process parameters on the surface roughness of a 3D-printed Co-Cr dental alloy produced via selective laser melting", Appl Sci, 6, pp.401~ (2016)
- Galo R, "Effects of chemical composition on the corrosion of dental alloys", Braz Dent J, 23, pp.141~148 (2012)
- Frankel GS, "Electrochemical techniques in corrosion: status, limitations, and needs", J Test Eval, 42, pp.517~538 (2008)
- Xin XZ, "Surface characteristics and corrosion properties of selective laser melted Co-Cr dental alloy after porcelain firing", Dent Mater, 30, pp.263~270 (2014)
- McCabe JF, "Applied dental materials", pp.4~84 (2008), Blackwell Publishing Ltd
- Schmalz G, "Biological interactions of dental cast alloys with oral tissues", Dent Mater, 18, pp.396~406 (2002)
- Viennot S, "Corrosion resistance of cobalt-chromium and palladium-silver alloys used in fixed prosthetic restorations", Eur J Oral Sci, 113, pp.90~95 (2005)
- Shin JC, "Effect of molybdenum on the microstructure and wear resistance of cobalt-base Stellite hardfacing alloys", Surf Coat Technol, 166, pp.117~126 (2003)
- Matković T, "Effects of Ni and Mo on the microstructure and some other properties of Co-Cr dental alloys", J Alloys Compd, 366, pp.293~297 (2004)
- Ren L, "A novel coping metal material CoCrCu alloy fabricated by selective laser melting with antimicrobial and antibiofilm properties", Mater Sci Eng C Mater Biol Appl, 67, pp.461~467 (2016)
- Siddharth R, "Quantitative analysis of leaching of different metals in human saliva from dental casting alloys : An in vivo study", J Indian Prosthodont Soc, 15, pp.206~210 (2015)
- Bergman M, "Corrosion in the oral cavity--potential local and systemic effects", Int Dent J, 36, pp.41~44 (1986)
- Sahasrabudhe H, "Laser processed calcium phosphate reinforced CoCrMo for load-bearing applications : Processing and wear induced damage evaluation", Acta Biomater, 66, pp.118~128 (2018)
- Bandyopadhyay A, "Additively manufactured calcium phosphate reinforced CoCrMo alloy : Bio-tribological and biocompatibility evaluation for load-bearing implants", Addit Manuf, 28, pp.312~324 (2019)
- Hodgson AWE, "Passive and transpassive behaviour of CoCrMo in simulated biological solutions", Electrochim Acta, 49, pp.2167~2178 (2004)
- Okazaki Y, "Comparison of metal release from various metallic biomaterials in vitro", Biomater, 26, pp.11~21 (2005)
- Tuna SH, "The influence of the pure metal components of four different casting alloys on the electrochemical properties of the alloys", Dent Mater, 25, pp.1096~1103 (2009)
- López-Alías JF, "Ion release from dental casting alloys as assessed by a continuous flow system : Nutritional and toxicological implications", Dent Mater, 22, pp.832~837 (2006)
- Wataha JC, "Biocompatibility of dental casting alloys : a review", J Prosthet Dent, 83, pp.223~234 (2000)
- Valero Vidal C, "Study of the adsorption process of bovine serum albumin on passivated surfaces of CoCrMo biomedical alloy", Electrochim Acta, 55, pp.8445~8452 (2010)
- Liverani E, "Fabrication of Co-Cr-Mo endoprosthetic ankle devices by means of Selective Laser Melting(SLM)", Mater Design, 106, pp.60~68 (2016)
- Kettelarij JA, "Cobalt, nickel and chromium release from dental tools and alloys", Contact Dermatitis, 70, pp.3~10 (2014)
- Xin XZ, "In vitro biocompatibility of Co-Cr alloy fabricated by selective laser melting or traditional casting techniques", Mater Lett, 88, pp.101~103 (2012)
- Muñoz AI, "Effect of the environment on wear ranking and corrosion of biomedical CoCrMo alloys", J Mater Sci Mater Med, 22, pp.437~450 (2011)
- Kurz W, "Fundamentals of solidification", pp.1~15 (1989), Trans Tech Publications
- Kruth JP, "Binding mechanisms in selective laser sintering and selective laser melting", Rapid Prototyp J, 11, pp.26~36 (2005)
- Prashanth K, "Microstructure and mechanical properties of Al-12Si produced by selective laser melting : Effect of heat treatment", Mater Sci Eng A, 590, pp.153~160 (2014)
- "Standard specification for cobalt-28 chromium-6 molybdenum alloy castings and casting alloy for surgical implants", ASTM International. ASTM F75-12, ~ (2012)
- Koutsoukis T, "Selective laser melting technique of Co-Cr dental alloys : A review of structure and properties and comparative analysis with other available techniques", J Prosthodont, 24, pp.303~312 (2015)
- Montero-Ocampo C, "Effect of fcchcp phase transformation produced by isothermal aging on the corrosion resistance of a Co-27Cr-5Mo-0.05C alloy", Metall Mater Trans A, 33, pp.2229~2235 (2002)