Curing Behavior and Adhesion Performance of Urea‐Melamine‐Formaldehyde (UMF) Resin by Staged Addition of Melamine
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
The objective of this research was to investigate the curing behavior and adhesion performance of urea‐melamine‐formaldehyde (UMF) resin for the four types of UMF-1, UMF-2, UMF-3, and UMF-4 which synthesized by the staged addition of melamine. Also, various network structures of these resin types were discussed based on their different curing behavior and adhesion performance. The curing behavior was evaluated by DMTA and thermal stability was checked by TGA. Adhesion performance was evaluated by dry and wet shear strengths and the pH value of each cured resin was checked to see its effect on the adhesion performance. The results indicated that the UMF-1 resin type by the addition of melamine initially with the urea and formaldehyde at the same F/(U+M) rate showed the lowest thermal stability, rigidity (△E'), temperature of tan δ maximum (Ttan δ), and wet shear strength, and pH value of cured resin. In wet shear strength, however, the UMF-4 resin type appears to be slightly higher than UMF-1 resin type.
Abstract
The objective of this research was to investigate the curing behavior and adhesion performance of urea‐melamine‐formaldehyde (UMF) resin for the four types of UMF-1, UMF-2, UMF-3, and UMF-4 which synthesized by the staged addition of melamine. Also, various network structures of these resin types were discussed based on their different curing behavior and adhesion performance. The curing behavior was evaluated by DMTA and thermal stability was checked by TGA. Adhesion performance was evaluated by dry and wet shear strengths and the pH value of each cured resin was checked to see its effect on the adhesion performance. The results indicated that the UMF-1 resin type by the addition of melamine initially with the urea and formaldehyde at the same F/(U+M) rate showed the lowest thermal stability, rigidity (△E'), temperature of tan δ maximum (Ttan δ), and wet shear strength, and pH value of cured resin. In wet shear strength, however, the UMF-4 resin type appears to be slightly higher than UMF-1 resin type.
참고문헌 (14)
- A. Kandelbauer, , J. Appl. Polym. Sci, 106, pp.2192~ (2007)
- A. Pizzi, , J. Appl. Polym. Sci, 58, pp.109~ (1995)
- A. T. Mercer, , J. Appl. Polym. Sci, 61, pp.1687~ (1996)
- B. Y. No, , J. Appl. Polym. Sci, 93, pp.2559~ (2004)
- B. Y. No, , J. Appl. Polym. Sci, 97(377) (2005)
- Hong, A. Pizzi, , J. Appl. Polym. Sci, 100, pp.4842~ (2006)
- L. A. Panangama, , J. Appl. Polym. Sci, 59, pp.2055~ (1996)
- L. Onic, , Int. J. Adhes. Adhes, 18, pp.89~ (1998)
- M. Higuchi, , J. Jap. Wood Res. Soc, 25, pp.630~ (1979)
- M. Properzi, , J. Appl. Polym. Sci, 81, pp.2821~ (2001)
- S. Kim, , J. Adhes. Sci. Technol, 17, pp.1369~ (2003)
- S. Kim, , J. Adhesion Sci. Technol, 20(8), pp.803~ (2006)
- S. Kim, , Thermochimica Acta, 444(2), pp.134~ (2006)
- T. Hirata, , J. Appl. Polym. Sci, 42, pp.3147~ (1991)