유한요소해석에 기반한 국내 고층아파트 T형 벽체의 횡보강영역 산정방법의 적합성 평가
Suitability Evaluation of Design Methods for Lateral Confinement Region of T-Shaped Walls Based on Finite Element Analysis
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Recently, high-rise residential buildings in Korea have adopted slender shear walls with irregular section shapes, such as T-shape, H-shape, and C-shape. In the seismic design of the slender shear walls, the transverse reinforcement for lateral confinement should be provided in the boundary elements to increase deformation capacity and subsequent ductility. However, in practice, the irregularity of the shear walls is not adequately considered, and the lateral confinement region is calculated for the rectangular wall segments. This study investigated the proper design method for lateral confinement regions using finite element analysis. The lateral confinement region was considered in analysis for two cases: 1) as a typical rectangular wall segment and 2) as an irregular wall. When the irregularity of the walls was considered, the compression zone depth was increased because the vertical reinforcement in the flange was addressed. The effect of lateral confinement design methods on the structural performance of the walls was directly compared under various design parameters, including the length of the flange, concrete compressive strength, vertical rebar layout, axial load ratio, and loading direction. According to the results of the parametric analysis, the peak strength and deformation capacity could be significantly increased when the lateral confinement region was calculated based on irregularly shaped walls, regardless of the design parameters. In addition, the effective compression zone was located within the lateral confinement region. Thus, it is recommended that the lateral confinement region of T-shaped walls is calculated by addressing the irregularity of the walls.
Abstract
Recently, high-rise residential buildings in Korea have adopted slender shear walls with irregular section shapes, such as T-shape, H-shape, and C-shape. In the seismic design of the slender shear walls, the transverse reinforcement for lateral confinement should be provided in the boundary elements to increase deformation capacity and subsequent ductility. However, in practice, the irregularity of the shear walls is not adequately considered, and the lateral confinement region is calculated for the rectangular wall segments. This study investigated the proper design method for lateral confinement regions using finite element analysis. The lateral confinement region was considered in analysis for two cases: 1) as a typical rectangular wall segment and 2) as an irregular wall. When the irregularity of the walls was considered, the compression zone depth was increased because the vertical reinforcement in the flange was addressed. The effect of lateral confinement design methods on the structural performance of the walls was directly compared under various design parameters, including the length of the flange, concrete compressive strength, vertical rebar layout, axial load ratio, and loading direction. According to the results of the parametric analysis, the peak strength and deformation capacity could be significantly increased when the lateral confinement region was calculated based on irregularly shaped walls, regardless of the design parameters. In addition, the effective compression zone was located within the lateral confinement region. Thus, it is recommended that the lateral confinement region of T-shaped walls is calculated by addressing the irregularity of the walls.
참고문헌 (24)
- 2023 Seismological annual report, "Korea Meteorological Administration", ~ (2023)
- 2023 Population and housing census results, "Statistics Korea", Statistics Korea, ~ (2023)
- ACI Committee 318, "Building Code Requirements for Structural Concrete and Commentary (ACI 318-19)", American Concrete Institute, ~ (2019)
- "KDS 14 20 00. Concrete Structural Design Code", Korea Construction Standards Center, ~ (2021)
- Bang JS, "Application of building using optimal design of irregular wall", Computational Structural Engineering, 28(1), pp.47~52 (2015)
- Nam HS, "Biaxial interaction and load contour method for reinforced concrete C-and H-shaped structural walls", Journal of the Korea Concrete Institute, 29(2), pp.189~200 (2017)
- Paulay T, "The ductility of structural walls", Bulletin of the New Zealand Society for Earthquake Engineering, 18(3), pp.250~269 (1985)
- Thomsen IV JH, "Displacement based design of reinforced concrete structural walls: An experimental investigation of walls with rectangular and T-shaped cross-sections", pp.1995
- Wallace JW, "Seismic design of RC structural walls. Part I: New code format", Journal of Structural Engineering, 121(1), pp.75~87 (1995)
- Segura JR, "Impact of geometry and detailing on drift capacity of slender walls", ACI Struct J, 115(3), pp.885~895 (2018)
- Kim HD, "Moment-curvature relationship of RC structural walls with confined boundary elements using pre-fabricated rectangular continuous hoops", J Comput Struct Eng Inst Korea, 35(1), pp.45~55 (2022)
- Chun YS, "Seismic performance of special shear wall with modified details in boundary element depending on axial load ratio", LHI Journal, 7(1), pp.31~41 (2016)
- Song JK, "Seismic performance of special structural walls using overlapping hoops instead of closed hoops", International Journal of Concrete Structures and Materials, 13(25) (2019)
- Tripathi M, "Bar buckling in ductile RC walls with different boundary zone detailing : Experimental investigation", Eng Struct, 198, pp.109544~ (2019)
- Kim SH, "Effect of boundary confinement on ductility of RC walls", Engineering Structures, 230, pp.111695~ (2021)
- Kim MS, "Cyclic loading test for reinforced concrete wall confined with prefabricated rectangular continuous hoops", Journal of Building Engineering, 97, pp.110681~ (2024)
- Hognestad E, "study of combined bending and axial load in reinforced concrete members", pp.1951
- Kim MS, "Seismic performance evaluation of RC structural walls with prefabricated rectangular continuous hoops", master, pp.2024
- Han SW, "Effect of edge confinement on deformation capacity in the isolated RC strcutural walls", J Korea Concr Inst, 11(6), pp.101~112 (1999)
- Vladimír Červenka, "ATENA Program Documentation Part1 Theroy", ~ (2022)
- Kupfer H, "Behavior of concrete under biaxial stresses", Journal ACI, Proceedings, 66(8), pp.656~666 (1969)
- Thomsen IV JH, "Displacement-Based design of slender reinforced concrete structural walls—Experimental verification", J Struct Eng, 130(4) (2004)
- Mander JB, "Theoretical stress-strain model for confined concrete", J Struct Eng, 114(8), pp.1804~1826 (1988)
- Recommendations for seismic design of reinforced concrete wall buildings based on studies of the 2010Maule, Chile earthquake, , National Institute of Standards and Technology, 322~, pp.NIST GCR 14-917-25 (2010)