횡압력을 받는 실선 보강판의 평균압축강도
Average Compressive Strengths of Stiffened Plates for In-Service Vessels Under Lateral Pressure
2
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
This paper presents estimation of average compressive strengths of three types of stiffened panels under lateral pressure and axial compression based on simplified formulas from CSRs and nonlinear FEAs. FEA scenarios are prepared based on the slenderness ratios of the stiffened panels used for in-service vessels. The seven step lateral pressures by 1bar increment are imposed on FE models assuming maximum 30m water height. The number of FEAs for FB-, AB-, and TB-stiffened panels is totally 189 times. FEA results show that existence of pressure can evolves significant reduction of ultimate strengths, meanwhile CSR formulas do not take into account the lateral pressure effect. Lateral pressure acting on the stiffened panel with higher column slenderness ratio more reduces the ultimate strengths than those with smaller column slenderness ratio. A new concept of relative average compressive strain energy instead of the ultimate strength is introduced in order to rationally compare the average compressive strength through complete compressive straining regime. The differences of the ultimate strengths between CSR formulas and FEA results are relatively small for FB- and AB-stiffened panels, but larger discrepancies of relative average compressive strain energies are shown.
Abstract
This paper presents estimation of average compressive strengths of three types of stiffened panels under lateral pressure and axial compression based on simplified formulas from CSRs and nonlinear FEAs. FEA scenarios are prepared based on the slenderness ratios of the stiffened panels used for in-service vessels. The seven step lateral pressures by 1bar increment are imposed on FE models assuming maximum 30m water height. The number of FEAs for FB-, AB-, and TB-stiffened panels is totally 189 times. FEA results show that existence of pressure can evolves significant reduction of ultimate strengths, meanwhile CSR formulas do not take into account the lateral pressure effect. Lateral pressure acting on the stiffened panel with higher column slenderness ratio more reduces the ultimate strengths than those with smaller column slenderness ratio. A new concept of relative average compressive strain energy instead of the ultimate strength is introduced in order to rationally compare the average compressive strength through complete compressive straining regime. The differences of the ultimate strengths between CSR formulas and FEA results are relatively small for FB- and AB-stiffened panels, but larger discrepancies of relative average compressive strain energies are shown.
참고문헌 (12)
- Ahn, J.W, "Buckling", Ultimate Strength of Perforated Plate according to Reinforcement Method around the Cutout, 2010, 1223~1231[DOI]
- Cho, S.R, "Post-Ultimate Behaviour of Stiffened Panels subjected to Axial Compression", 2nd International Conference on Thin-Walled Structures, pp.433~440 (1998)
- Gordo, J.M, "Approximate Assessment of the Ultimate Longitudinal Strength of the Hull Girder", Journal of Ship Research, 40(1), pp.60~69 (1996)
- "Common Structural Rules for Bulk Carriers" (2010)[URL]
- "Common Structural Rules for Double Hull Oil Tankers" (2010)[URL]
- Lee, J.S., "Reliability Analysis of Continuous Structural System", 박사, pp.1989
- Lee, J.W, "Buckling", Ultimate Strength of steel-plated structure according to Initial Deflection Shape, 2010, 1232~1238[DOI]
- Lin, Y.T, "Ship Longitudinal Strength", 박사, pp.1985
- 정준모, "실선 보강판의 세장비 분포 및 평균 압축 강도 비교 연구", 대한조선학회 논문집, 47(5), pp.709~718 (2010), 대한조선학회
- Paik, J.K, "Ultimate Strength Formulations for Stiffened Panels under Combined Axial Load, In-Plane Bending and Lateral Pressure: a Benchmark Study", Thin-Walled Structures, 40(1), pp.45~83 (2002)
- Paik, J.K, "Ultimate Limit State Design of Steel-Plated Structures" (2002), Wiley
- Smith, C.S, "Strength and Stiffness of Ships' Plating under In-plane Compression and Tension", RINA Transactions, 130, pp.277~296 (1988)