Optimal Design of 3D Printer based Piezo-driven Vertical Micro-positioning Stage
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
This paper presents the development of a 3D printer based piezo-driven vertical micro-positioning stage. The stage consists of two flexure bridge structures which amplify and transfer the horizontal motion of the piezo-element into vertical motion of the end-effector. The stage is fabricated with ABS material using a precision 3D printer. This enables a one-body design eliminating the need for assembly, and significantly increases the freedom in design while shortening fabrication time. The design of the stage was optimized using response surface analysis method. Experimental results are presented which demonstrate 100nm stepping in the vertical out-of-plane direction. The results demonstrate the future possibilities of applying 3D printers and ABS material in fabricating linear driven motion stages.
Abstract
This paper presents the development of a 3D printer based piezo-driven vertical micro-positioning stage. The stage consists of two flexure bridge structures which amplify and transfer the horizontal motion of the piezo-element into vertical motion of the end-effector. The stage is fabricated with ABS material using a precision 3D printer. This enables a one-body design eliminating the need for assembly, and significantly increases the freedom in design while shortening fabrication time. The design of the stage was optimized using response surface analysis method. Experimental results are presented which demonstrate 100nm stepping in the vertical out-of-plane direction. The results demonstrate the future possibilities of applying 3D printers and ABS material in fabricating linear driven motion stages.
참고문헌 (15)
- B. H. Kang, "Analysis and Design of Parallel Mechanisms With Flexure Joints", IEEE Transactions On Robotics, 21(6), pp.1179~1185 (2005)
- S. B. Choi, "Fine Motion Control of a Moving Stage using a Piezo-actuator Associated with a Displacement Amplifier", Smart Mater. Struct, 14(1), pp.222~230 (2005)
- H. W. Ma, "Analysis of the displacement amplification ratio of bridge-type flexure hinge", Sensors and Actuators, A, 132, pp.730~736 (2006)
- J. H. Kim, "Development and optimization of 3-D bridge-type hinge mechanisms", Sensors and Actuators, A, 166, pp.530~538 (2004)
- J. S. Kim, "Design of 3-DOF (Z-translation, Pitch, Roll motion) precise tilt table for a large surface workpiece with micro features to compensate set-up", J. of KSMT Fall Conference, pp.28~33 (2006)
- P. Gao, "A New Piezo-driven Precision Micro-positioning Stage utilizing Flexure Hinges", Nanotechnology, 10(4), pp.394~398 (1999)
- T. F. Lu, "A Three-DOF Compliant Micro-motion Stage with Flexure Hinges", Ind. Robot, 31(4), pp.355~361 (2004)
- K. Hu, "Design, Implementation, and Control of a Six-Axis Compliant Stage", Rev. Sci. Instrum., 79 (2008)
- K. H. Kwak, "Global 3D Printer Industry Technology Trends Analysis", J. of the KSME, 53(10), pp.58~64 (2013)
- J. H. Rho, "Rapid Prototyping with Vehicle Modeling Function and 3D Printer", Proc. of KSAE Annual Conference, pp.2541~2544 (2009)
- 김호찬, "ThermoJet 3D 프린터로 직접 제작한 패턴과 세라믹쉘 주조법을 이용한 기능성 시제품의 쾌속제작", 한국정밀공학회지, 23(8), pp.203~210 (2006), 한국정밀공학회
- 정호제, "3D 프린터를 사용한 정밀 스테이지의 제작", 한국정밀공학회지, 31(3), pp.277~283 (2014), 한국정밀공학회
- Jung H. Kim, "Visually Servoed 3-D Alignment of Multiple Objects with Sub-nanometer Precision", IEEE Trans. on Nanotechnology, 7(3) (2008)
- 김정현, "Emulation of anti-alias filtering in vision based motion measurement", 로봇학회 논문지, 6(1), pp.18~26 (2011), 한국로봇학회
- 이종배, "미세 작업을 위한 마이크로-나노 로봇개발", 로봇학회 논문지, 2(1), pp.64~71 (2007), 한국로봇학회