Factors affecting surface roughness of Al2O3 films deposited on Cu substrates by an aerosol deposition method
0
조회
0
다운로드
3
인용
0
참고문헌
키워드
초록
In an aerosol deposition method, factors affecting the surface roughness of Al2O3 thick films deposited on Cu substrates at room temperature were studied to propose guidelines for the growth of aerosol-deposited ceramic films with a flat and smooth surface morphology. The surface roughness and deposition rates of aerosol-deposited Al2O3 films strongly depended on the initial surface roughness of substrates. Even on flat substrates, however, their surface roughness became worse with an increase of their film thickness. Through the investigation of surface morphologies from the initial growth stages to the final,it was revealed that the deterioration of the surface roughness of Al2O3 films on flat substrates was substantially associated with the evolution of craters during the deposition. The fundamental cause of these results was explained by impact of hard Al2O3 particles above 1 ìm in size by comparison with the surface morphologies of the aerosol-deposited Ag or polyimide films.
Abstract
In an aerosol deposition method, factors affecting the surface roughness of Al2O3 thick films deposited on Cu substrates at room temperature were studied to propose guidelines for the growth of aerosol-deposited ceramic films with a flat and smooth surface morphology. The surface roughness and deposition rates of aerosol-deposited Al2O3 films strongly depended on the initial surface roughness of substrates. Even on flat substrates, however, their surface roughness became worse with an increase of their film thickness. Through the investigation of surface morphologies from the initial growth stages to the final,it was revealed that the deterioration of the surface roughness of Al2O3 films on flat substrates was substantially associated with the evolution of craters during the deposition. The fundamental cause of these results was explained by impact of hard Al2O3 particles above 1 ìm in size by comparison with the surface morphologies of the aerosol-deposited Ag or polyimide films.
참고문헌 (16)
- G. Vandewalle, , Philips J. Res., 51, pp.353~361 (1998)
- R. Tummala, , IEEE Trans. Advanced Packaging, 27, pp.241~249 (2004)
- E. Wong, , IEEE Trans. VLSI Systems, 14, pp.553~557 (2006)
- J.R. Minz, , IEEE Trans. Compo. Packaging Tech., 30, pp.805~812 (2007)
- K.F. Becker, , IEEE Trans. Advanced Packaging, 27, pp.268~277 (2004)
- Q. Yang, , Mater. Lett, 63, pp.406~408 (2009)
- Y. Imanaka, , J. Cryst. Growth, 275, pp.1314~1319 (2005)
- J. Akedo, , J. Am. Ceram. Soc., 89, pp.1834~1839 (2006)
- M. Lebedev, , J. Cryst. Growth, 275, pp.1301~1306 (2005)
- J. Akedo, , J. Thermal Spray Tech., 17(2), pp.181~198 (2008)
- J.M. Bennelt, , Meas. Sci. Technol, 3, pp.1119~1127 (1992)
- S. Gan, , Electronic Engineering, 84, pp.1806~1809 (2007)
- J.H. Pack, , Jpn. J. Appl. Phys., 45, pp.419~427 (2006)
- H. Hatono, , J. Appl. Ceram. Technol, 3(6), pp.419~427 (2006)
- S.M. Nam, , Jpn. J. Appl. Phys, 43, pp.5414~5418 (2004)
- H. Ha, , Jpn. J. Appl. Phys., 46, pp.6915~6919 (2007)