A comparative study on tribological characteristics of Ti-6Al-4V and Ti-6Al-4V-ELI alloys using hybrid nanoparticles (Al2O3 /MWCNT) cutting fluid
1
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
Selection of nanometer sized particles for preparation of hybrid cutting lubrication changes the behavior of the heat transferarea during the turning process. Also, addition of nano-particles to the base cutting lubrication significantly alters theproperties in lubrication by reducing the friction during the turning process. These experimental investigations were carriedout for four turning process parameters namely speed of cutting, feed of cutting, axial depth of cut and hybrid cuttinglubrication (MWCNT and Al2O3). In this investigation, nano cutting lubrication was prepared by adding 1 and 2 % volumeconcentration of MWCNT and Al2O3 nanosized particles to the industrial cutting fluid. In the turning process, friction betweenthe cutting tool and workpiece (Ti-6Al-4V and Ti-6Al-4V-ELI) is a leading key issue for the outcome of the quality. From theinvestigation study, it has been observed that selected turning process parameters and cutting lubricants have a direct influenceon coefficient of friction and surface roughness. The conclusion of investigation reveals that turning of Ti-6Al-4V and Ti-6Al-4V ELI (Extra Low Interstitials) under nano cutting lubrication improves the quality compared to normal cutting lubrication
Abstract
Selection of nanometer sized particles for preparation of hybrid cutting lubrication changes the behavior of the heat transferarea during the turning process. Also, addition of nano-particles to the base cutting lubrication significantly alters theproperties in lubrication by reducing the friction during the turning process. These experimental investigations were carriedout for four turning process parameters namely speed of cutting, feed of cutting, axial depth of cut and hybrid cuttinglubrication (MWCNT and Al2O3). In this investigation, nano cutting lubrication was prepared by adding 1 and 2 % volumeconcentration of MWCNT and Al2O3 nanosized particles to the industrial cutting fluid. In the turning process, friction betweenthe cutting tool and workpiece (Ti-6Al-4V and Ti-6Al-4V-ELI) is a leading key issue for the outcome of the quality. From theinvestigation study, it has been observed that selected turning process parameters and cutting lubricants have a direct influenceon coefficient of friction and surface roughness. The conclusion of investigation reveals that turning of Ti-6Al-4V and Ti-6Al-4V ELI (Extra Low Interstitials) under nano cutting lubrication improves the quality compared to normal cutting lubrication
참고문헌 (23)
- C. Manivel, , Dg. J. Nanomater. Biostructures, 15(3), pp.787~798 (2020)
- Muhammet Ceylan, "Wear behavior of irregular shape Ti6Al4V powder reinforced with carbon nanotubes", Journal of Ceramic Processing Research, 21(5), pp.539~546 (2020), 청정에너지연구소[DOI]
- M. Mia, , J Cleaner Prod, 210, pp.121~133 (2019)
- S. Pradhan, , J. Mater. Res. Technol, 8(5), pp.4849~4862 (2019)
- M. A. Sofuoglu, , Sadhana J, 46(2), pp.1~9 (2021)
- V. Singh, , J. Manuf. Process, 62, pp.378~387 (2021)
- A. Thakur, , Silicon, 12(1), pp.71~85 (2020)
- Muhammad Shahid, "Synthesis and mechanical characterization of alumina based composite material for armor application", Journal of Ceramic Processing Research, 22(2), pp.149~157 (2021), 청정에너지연구소[DOI]
- T. Nithyanandhan, "Development of bamboo stem Ash-Al-Hybrid reinforced with Al2O3 produced by stir casting technique", Journal of Ceramic Processing Research, 22(4), pp.369~376 (2021), 청정에너지연구소[DOI]
- R. K. Singh, , J. Clean. Prod, 162, pp.830~845 (2017)
- D. Setti, , Int. J. Machine Tools and Manuf, 88, pp.237~248 (2015)
- M. K. Sinha, , J. Clean. Prod, 141, pp.1359~1375 (2017)
- B. Li, , J. Clean. Prod, 154, pp.1~11 (2017)
- M. A. H. M. Shariff, , In Intelligent Manufacturing and Mechatronics, 18, pp.365~372 (2021)
- Y. Touggui, , Int. J. Adv. Manuf. Technol, 115, pp.3983~3997 (2021)
- R. Anand, , Tribology Transactions, 64(2), pp.350~366 (2021)
- D.R. Joshua, "Experimental investigation and optimization of pulse electrodeposition parameters for Ni-TiO2 coating on Inconel 617 using TOPSIS technique", Journal of Ceramic Processing Research, 23(1), pp.69~78 (2022), 청정에너지연구소[DOI]
- C. Chanakyan, "Parametric studies in friction stir welding on Al-Mg alloy with (HCHCr) tool by Taguchi based desirability function analysis (DFA)", Journal of Ceramic Processing Research, 21(6), pp.647~655 (2020), 청정에너지연구소[DOI]
- N. Zeelanbasha, , Int. J. Operat. Res, 38(2), pp.221~254 (2020)
- Z. Zeelanbasha, , Transactions of FAMENA, 42(3), pp.115~128 (2018)
- N. Li, , Adv. Manuf, 7(2), pp.142~154 (2019)
- M. Linus, , Procedia Cirp, 58, pp.163~168 (2017)
- Senthilkumar KM, "Optimization of stir casting process parameter using response surface meth odology", Journal of Ceramic Processing Research, 23(2), pp.233~236 (2022), 청정에너지연구소[DOI]