Influence of Droplet Size and Oil Viscosity on the Descending Velocity of Droplets Using Water Model With and Without Stirring
0
조회
0
다운로드
0
인용
0
참고문헌
키워드
초록
Metal emulsions have been studied for several decades as a method of increasing the efficiency of the steelmaking process. This study was performed using a water model, observable at room temperature, to compensate for the disadvantages of the high-temperature experiment, the results of which are difficult to observe visually. As a substitute for metal-in-slag emulsions, experiments were conducted by dropping distilled water into silicone oil and comparing the results with the results of a calculation by momentum balance equations. The descending velocity of the water droplet decreased as the diameter of the droplet and viscosity of the fluid (silicon oil) increased. To simulate the descending velocity of a water droplet in silicon oil under stirring conditions, the flow rate of the fluid (silicon oil) was measured by particle image velocimetry (PIV) methods. The calculation of the descending velocity of the water droplet was in good agreement with the measured values, with and without stirring a viscous silicone oil.
Abstract
Metal emulsions have been studied for several decades as a method of increasing the efficiency of the steelmaking process. This study was performed using a water model, observable at room temperature, to compensate for the disadvantages of the high-temperature experiment, the results of which are difficult to observe visually. As a substitute for metal-in-slag emulsions, experiments were conducted by dropping distilled water into silicone oil and comparing the results with the results of a calculation by momentum balance equations. The descending velocity of the water droplet decreased as the diameter of the droplet and viscosity of the fluid (silicon oil) increased. To simulate the descending velocity of a water droplet in silicon oil under stirring conditions, the flow rate of the fluid (silicon oil) was measured by particle image velocimetry (PIV) methods. The calculation of the descending velocity of the water droplet was in good agreement with the measured values, with and without stirring a viscous silicone oil.
참고문헌 (20)
- Duangsuwan, W., "Feasibility of N2", Sunflower Oil Compound Drop Formation in Methanol Induced by Bubble Train, 2010, pp.56(12), 3274~3278
- Shui, L., "Understanding of Bath Surface Wave in Bottom Blown Copper Smelting Furnace", Metall. Mater. Trans B, 47B, pp.135~144 (2016)
- Soares, J. B. P., "Polymeric Dispersions: Principles and Applications. NATO ASI Series, Vol. 335" (1997), Springer
- Martin, M., "Emulsion Analysis in a Gas", Liquid, Can. J. Chem. Eng, pp.2004, 82[DOI]
- Iguchi, M., "Model study of fluid flow phenomena in a bottom blown bath in the presence of reverse emulsification", ISIJ Inter"national, 38(10), pp.1080~1085 (1998)
- He, Q. L., "A model study of residence time of metal droplets in the slag in BOF steelmaking", ISIJ International, 30(5), pp.356~361 (1990)
- Lin, Z., "Modeling of metallurgical emulsions", Metall. Mater. Trans. B, 25B(6), pp.855~864 (1994)
- Gaye, H., "Oxidation kinetics of iron alloy drops in oxidizing slags", Metall. Trans. B, 8B, pp.409~415 (1977)
- Min, D. J., "Rate of reduction of FeO in slag by Fe-C drops", Metall. Trans. B, 23B, pp.29~37 (1992)
- Gu, K., "Dephosphorization Kinetics between Bloated Metal Droplets and Slag Containing FeO: The Influence of CO Bubbles on the Mass Transfer of Phosphorus in the Metal", Metall. Mater. Trans B, 48B, pp.2984~3001 (2017)
- Reiter, G., "Observations of physical phenomena occurring during passage of bubbles through liquid", liquid interfaces, 1992, pp.32(1), 50~56
- Reiter, G., "Characteristics of entrainment at liquid", liquid interfaces due to rising bubbles, 1992, pp.32(1), 57~65
- Song, D. -Y., "Influence of Bottom Bubbling Rate on Formation of Metal Emulsion in Sn-Sb-Cu Alloy and Molten Salt System", ISIJ Int, 57, pp.236~244 (2017)
- Song, D. -Y., "Influence of Bottom Bubbling Condition on Metal Emulsion Formation in Lead-Salt System", ISIJ Int, 50, pp.1539~1545 (2010)
- Yoshida, H., "Influence of the Interfacial Tension on the Droplet Formation by Bubble Rupture in Sn(Te)and Salt System", ISIJ Int, 56, pp.1902~1909 (2016)
- Liu, J., "Metal Emulsion Behavior of Droplets with Various Sizes in the Na2B4O7", Sn Alloy System by Bottom Bubbling Gas and its Comparison with the Chloride, Metall. Mater. Trans B, pp.2017, 48B[DOI]
- Horii, K., "Processing and Reusing Technologies for Steelmaking Slag", Nippon steel Tech. Rep, 104, pp.122~129 (2013)
- Song, D. Y., "Modeling of ascending", descending velocity of metal droplet emulsified in Pb-salt system, 2012, pp.43B(4), 973~983
- Song, D. Y., "Study of Two Phase Emulsion Systems", Trans. Indian Inst. Met, 70, pp.2027~2038 (2017)
- Conejo, A. N., "Effects of Top Layer, Nozzle Arrangement, and Gas Flow Rate on Mixing Time in Agitated Ladles by Bottom Gas Injection", Metall. Mater. Trans. B, 44B, pp.914~923 (2013)