I-fiber 스티칭 공법이 적용된 Single-lap Joint의 강도 특성 및 파손 신호 검출 연구
A Study on the Strength Characteristics and Failure Detection of Single-lap Joints with I-fiber Stitching Method
0
조회
0
다운로드
1
인용
0
참고문헌
키워드
초록
적층 복합재의 특성상 두께 방향 물성이 취약하여 비틀림, 저속충격, 피로 하중 등 복합 하중을 받게 되면 재료 내부의 미세크랙 진전을 통해 층간분리 현상이 발생하게 된다. 이를 방지하고자 Z-pinning, Stitching 등 다양한 3차원 보강 공법과 구조물의 미세균열을 실시간으로 검출하는 구조 건전성 감시 기법이 꾸준히 연구되고 있다. 본 논문에서는 I-fiber 스티칭 공법으로 보강된 Single-lap joint를 Co-curing 방법으로 제작하였으며, 제작된 시편의 강도 및 파손신호 검출 특성을 평가하였다. 균열과 파손신호 검출을 위하여 전기저항법과 AE법을 사용하였으며, 신호분석을 위한 전용회로를 제작하여 인장시험 중의 파손 신호를 분석하였다. 실험결과, I-fiber 스티칭으로 보강된 Single-lap joint 시편은 보강이 없는 Co-cured singlelap joint 시편에 비해 강도가 약 44.6% 향상되었다. 또한, I-fiber로 보강된 Single-lap joint 시편은 강도 향상과 더불어 전기저항법과 AE법에 의한 파손 검출이 모두 가능하므로 파손 모니터링에도 효과적인 구조임을 확인하였다.
Abstract
When a complex load such as torsion, low-speed impact, or fatigue load is applied, the properties in the thickness direction are weakened through microcracks inside the material due to the nature of the laminated composite material, and delamination occurs. To prevent the interlaminar delamination, various three-dimensional reinforcement methods such as Z-pinning and stitching, and structural health monitoring techniques that detect the microcrack of structures in real time have been continuously studied. In this paper, the single-lap joints with I-fiber stitching process were manufactured by a co-curing method and their strengths and failure detection capability were evaluated. AE and electric resistance method were used for detection of crack and failure signal and electric circuit for signal analysis was manufactured, and failure signal was analyzed during the tensile test of a single-lap joint. From the experiment, the strength of the single lap joint reinforced by I-fiber stitching process was improved by about 44.6% compared to the co-cured single lap joint without reinforcement. In addition, as the single-lap joint reinforced by Ifiber stitching process can detect failure in both the electrical resistance method and the AE method, it has been proven to be an effective structure for failure monitoring as well as strength improvement.
참고문헌 (14)
- Plain, K. P., "The Effect of Stitch Incline Angle on Mode I Fracture Toughness – Experimental and Modelling", Composite Structures, 92(7), pp.1620~1630 (2010)
- Aymerich, F., "Effect of Stitching on the Static and Fatigue Performance of Co-cured Composite Single-lap Joints", Journal Composite Materials, 38(3), pp.243~257 (2004)
- Beylergil, B., "Experimental and Numerical Analysis of Single Lap Composite Joints with Interadherend Fibers", Composites : Part B, 42(7), pp.1885~1896 (2011)
- Mouritz, A. P., "A Mechanistic Approach to the Properties of Stitched Laminates", Composites Part A : Applied Science and Manufacturing, 31(1), pp.1~27 (2000)
- Ji, H., "Fatigue Characteristics of Stainless Steel Pin-reinforced Composite Hat Joints", Composite Structures, 108, pp.49~56 (2014)
- Chang, P., "Properties and Failure Mechanisms of Pinned Composite Lap Joints in Monotonic and Cyclic Tension", Composites Science and Technology, 66(13), pp.2163~2176 (2006)
- Steeves, C. A., "In-plane Properties of Composite Laminates with Through-thickness Pin Reinforcement", International Journal of Solids and Structures, 43(10), pp.3197~3212 (2006)
- 송상훈, "I-fiber Stitching 공법을 적용한 복합재료 Single-lap Joint의 Stitching 패턴과 각도에 따른 정적 강도 연구", Composites Research, 33(5), pp.296~301 (2020), 한국복합재료학회
- Kim, C. H., "Failure Strength of Composite T-joints Prepared Using Anew 1-thread Stitching Process", Composite Structures, 178, pp.225~231 (2017)
- An, W. -J., "Static Strength of RTM Composite Joint with I-fiber Stitching Process", Composite Structures, 210, pp.348~353 (2019)
- Kim, C. H., "Impact Characteristics of Composite Panel Stitched by I-fiber Process", Composites Part A, 127, pp.105644~ (2019)
- Kang, M. H., "Fatigue Life Evaluation and Crack Detection of the Adhesive Joint with Carbon Nanotubes", Composite Structures, 108, pp.417~422 (2014)
- Baek, S. J., "Defect Detection of Composite Adhesive Joints Using Electrical Resistance Method", Composite Structures, 220, pp.179~184 (2019)
- 김철환, "Composite Fracture Detection Capabilities of FBG Sensor and AE Sensor", Composites Research, 27(4), pp.154~157 (2014), 한국복합재료학회